manualshive.com logo in svg

Siemens 1PH818, Инструкция по эксплуатации и установке

Поделиться
Скачать
Siemens 1PH818 Скачать руководство пользователя страница 108

For the "Performance" version, only use these special greases.

Table 9-6

Grease for the "Performance" version

Manufacturer

Grease type

Lubcon

Sintono GPE702

NOTICE
Damage caused by mixing lubrication types
Mixing different greases adversely affects the lubricating properties. Only the manufacturer 

provides a guarantee as to whether certain greases can be mixed.
● Never mix different greases.

Regreasing

Regreasing data are stamped on the lubricant plate of the machine:
● Relubrication intervals in operating hours
● Regreasing amount in grams
● Grease type
Regrease the bearing at the latest every 12 months irrespective of the actual number of 

operating hours. 

NOTICE
Relubrication intervals
The relubrication intervals for roller bearings are different from the servicing intervals for the 

machine. The roller bearings may be damaged if the relubrication intervals are not complied 

with. 
● Pay attention to the instructions on the lubricant plate.

Grease replacement intervals
The grease replacement intervals in these operating instructions or the relubrication intervals 

indicated on the plate apply for the following conditions:
● Normal load
● Operation at speeds in accordance with the rating plate
● Low-vibration operation
● Neutral ambient air
● High-quality roller bearing greases
In the case of unfavorable conditions, reduce the relubrication intervals after prior consultation 

with the manufacturer.

Maintenance
9.2 Inspection and maintenance

SIMOTICS M-1PH8  1PH818., 1PH822.

108

Operating Instructions 07/2016

Содержание 1PH818







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды