Siemens 1PH818 Скачать руководство пользователя страница 102

Страница: 102 / 198

WARNING

Machine damage
If the machine is not maintained it can suffer damage. This can cause faults which can result

in eventual or immediate death, serious injury or material damage.
Perform regular maintenance on the machine.

CAUTION

Dust disturbances when working with compressed air
When cleaning with compressed air, dust, metal chips, or cleaning agents can be whirled up.

Injuries can result.
When cleaning using compressed air, make sure you use suitable extraction equipment and

wear protective equipment (safety goggles, protective suit, etc.).

NOTICE
Damage to insulation
If metal swarf enters the winding head when cleaning with compressed air, this can damage

the insulation. Clearance and creepage distances can be undershot. This may cause damage

to the machine extending to total failure.
When cleaning with compressed air, ensure there is adequate extraction.

NOTICE
Machine damage caused by foreign bodies
Foreign bodies such as dirt, tools or loose components, such as screws etc., can be left by

accident inside the machine after maintenance is performed. These can cause short circuits,

reduce the performance of the cooling system or increase noise in operation. They can also

damage the machine.
● When carrying out maintenance work, make sure that no foreign bodies are left in or on

the machine.

● Securely attach all loose parts again once you have completed the maintenance

procedures.

● Carefully remove any dirt.

Note
Operating conditions and characteristics can vary widely. For this reason, only general

intervals for inspection and maintenance measures can be specified here.

9.2.1

Inspections in the event of faults

Natural disasters or unusual operating conditions, such as overloading or short circuit, are

faults that overload the machine electrically or mechanically.

Maintenance
9.2 Inspection and maintenance

SIMOTICS M-1PH8 1PH818., 1PH822.

102

Operating Instructions 07/2016

Содержание 1PH818







































































































































































































Результаты поиска

Содержание 1PH818

Отзывы:

Бренды по названию

Популярные бренды

Siemens 1PH818, Инструкция по эксплуатации и установке

Результаты поиска

Содержание 1PH818

Отзывы:

Бренды по названию

Популярные бренды