Siemens 1LE5 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 142

background image

3.3

Installation

3.3.1

Machine design

Machines of this series are low-voltage three-phase induction drives with a cylindrical shaft
extension and keyway. They can be supplied as single-speed machines with different efficiency
classes or as pole changing machines for several speeds.

In the case of machines with feet (IM B3 type of construction), the feet are cast or bolted on.

It is possible to change over the bolted on mounting feet on the machine enclosure, for
example to change the terminal box position; only authorized retrofit partners may carry out
this work.
Measures for alignment and mounting (Page 57)

3.3.2

Regulations

The regulations and standards used as the basis for designing and testing this machine are
stamped on the rating plate. The machine design basically complies with the following
standards:

Table 3-1

Applicable general regulations

Feature

Standard

EAC

Dimensioning and operating behavior

EN/IEC 60034-1

GOST IEC 60034-1

Procedure for determining the losses and the efficiency of rotating electrical
machines and inspections

EN/IEC 60034-2-1
EN/IEC 60034-2-2
EN/IEC 60034-2-3

GOST IEC 60034-2-1
GOST IEC 60034-2-2
GOST IEC 60034-2-3

Degree of protection

EN/IEC 60034-5

GOST IEC 60034-5

Cooling

EN/IEC 60034-6

GOST R IEC 60034-6

Type of construction

EN/IEC 60034-7

GOST R IEC 60034-7

Terminal designations and direction of rotation

EN/IEC 60034-8

GOST 26772

Noise emission

EN/IEC 60034-9

GOST IEC 60034-9

Integrated thermal protection

EN/IEC 60034-11

GOST 27888

Starting characteristics of rotating electrical machines

EN/IEC 60034-12

GOST IEC 60034-12

Vibration severity grades

EN/IEC 60034-14

GOST IEC 60034-14

Efficiency classification of three-phase squirrel-cage induction motors

EN/
IEC 60034-30-1

GOST IEC 60034-30-1

IEC standard voltages

IEC 60038

GOST R IEC 61800-1

3.3.3

Cooling and ventilation

The machines of this series are three-phase induction machines with a closed primary (internal)
cooling circuit and an open secondary cooling circuit (surface cooling). The surface cooling
varies depending on the version.

Description

3.3 Installation

1LE5, 1PC4 shaft heights 280 ... 355
Operating Instructions, 11/2022, A5E41454666A

27

«
...
27
28
29
30
31
...
»

Содержание 1LE5















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1LE5

Бренд: BAFANG Страницы: 6

EC FSE 400 - SERVICE 2002 & 2003

Бренд: GAS GAS Страницы: 74

Crankcase for Harley-Davidson

Бренд: S&S Cycle Страницы: 12

Бренд: Polini Страницы: 32

Бренд: MTD Страницы: 36

Бренд: Rotax Страницы: 13

Бренд: de Gier Страницы: 26

Бренд: Black Bruin Страницы: 70

Бренд: FUTABA Страницы: 3

Бренд: Lombardini Страницы: 50

Бренд: Lombardini Страницы: 114

Бренд: Gude Страницы: 52

Бренд: Stiga Страницы: 40

Shire 15 Work Boat YM

Бренд: Barrus Страницы: 44

Бренд: Torini Страницы: 16

Бренд: Marine Power Страницы: 56

Бренд: ZIEHL-ABEGG Страницы: 8

Бренд: Briggs & Stratton Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды