Siemens 1LE5 Скачать руководство пользователя страница 132

Страница: 132 / 142

11.4

Preparing for disassembly

Disassembly of the machine must be carried out and/or supervised by qualified personnel with
appropriate expert knowledge.

1. Contact a certified waste disposal organization in your vicinity. Clarify what is expected in

terms of the quality of dismantling the machine and provision of the components.

2. Carefully follow the 5 safety rules (Page 19).

3. Disconnect all electrical connections and remove all cables.

4. Remove all liquids e.g. oil and cooling liquids. Collect the liquids separately and dispose of

them in a professional manner.

5. Detach the machine fixings.

6. Transport the machine to a suitable location for disassembly.

11.5

Dismantling the machine

Dismantle the machine using the general procedures commonly used in mechanical
engineering.

WARNING

Machine parts can fall

The machine is made up of heavy parts. These parts are liable to fall during dismantling. This
can result in death, serious injury or material damage.
• Before you release any machine parts, secure them so that they cannot fall.

11.6

Disposal of components

Components

The machines consist mainly of steel and various proportions of copper and aluminum. Metals
are generally considered to be unlimitedly recyclable.

Sort the components for recycling according to whether they are:

• Iron and steel

• Aluminum

• Non-ferrous metal, e.g. windings

The winding insulation is incinerated during copper recycling.

• Insulating materials

• Cables and wires

• Electronic waste

Disposal
11.6 Disposal of components

1LE5, 1PC4 shaft heights 280 ... 355

130

Operating Instructions, 11/2022, A5E41454666A

Содержание 1LE5















































































































































Результаты поиска

Содержание 1LE5

Отзывы:

Похожие инструкции для 1LE5

Бренды по названию

Популярные бренды

Siemens 1LE5, Руководство по эксплуатации

Результаты поиска

Содержание 1LE5

Отзывы:

Похожие инструкции для 1LE5

Бренды по названию

Популярные бренды