Siemens Healthcare XPRECIA STRIDE Скачать руководство пользователя страница 36

Страница: 36 / 59

Xprecia Stride

User Guide

5. Performing troubleshooting and maintenance

Learning about system messages

Stride stores and lets you retrieve a minimum of 300
system messages, comprised of warning messages and
error messages:

Warning message

Stride detects a problem, displays

a message, and once you correct the problem, you can
continue the test. These messages are stored in the
Events log.

Error message

Stride detects a problem, displays a

message, but you can’t continue testing. These messages
are stored with the test results.

Viewing the system messages

INSTRUCTIONS

1. On the Home screen, tap

2. Tap

Operator 3245W

9:58am 10.05.2015

02-07

01-02

01-06

01-05

9:46am 10.05.2015

Operator 2980W

9:42am 10.05.2015

9:36am 10.05.2015

10:00 am

10.05.2015

The most recent system messages display at the top of the list,

showing the time, date, warning, or error code.

Troubleshooting system messages

Warning messages

CODE MESSAGE

PROBABLE CAUSE

POSSIBLE SOLUTION

01-01

Barcode scan error

Stride encountered an unknown error
while scanning.

Try to scan again. If the error continues, turn Stride off
and on.

01-02

Battery Low

Your batteries are running out.

Replace with 3 new AA batteries.

01-04

Invalid Login

An incorrect Operator ID (OID) was
entered.

Try reentering the Operator ID (OID).

01-05

Invalid OID

An incorrect Operator ID (OID)
was entered.

Try reentering the Operator ID (OID).

01-06

Invalid PID

An incorrect Patient ID (PID)
was entered.

Try reentering the Patient ID (PID).

01-07

LQC Expiration date exceeded

Your lot of control solution has
reached its expiration date.

Verify the Stride date setting is correct and then redo
the test using a different control lot.

01-08

OID delete failed

Stride encountered an error trying to
delete the Operator ID (OID).

Make sure you have administrator rights to delete an
OID and that the OID is valid.

01-09

OID list full

The operator list is full.

Remove one or more operators from the list.

01-10

Test strip port protective cap missing

The test strip port protective cap was
not installed properly.

Align tab in cap with slot and slide cap until it
clicks into place.

01-11

Test strip inserted early

The test strip was inserted before Stride
requested.

Remove test strip and insert when Stride prompts you.

01-12

Test strip and vial do not match

You may have scanned a test strip from
a different lot.

Verify the test strip is from the correct vial and rescan.
If the error continues, cancel the test and repeat using
a new test strip from the vial.

Содержание XPRECIA STRIDE




























































Результаты поиска

Содержание XPRECIA STRIDE

Отзывы:

Siemens Healthcare XPRECIA STRIDE, Руководство пользователя, Страница: 36 / 59

Результаты поиска

Содержание XPRECIA STRIDE

Отзывы: