NONFOLD TC-65 STOOL TABLE
MESA CON BANCOS FIJOS TC-65
IMPORTANT: Always provide Serial No. when
ordering parts
.
IMPORTANTE: Cuando ordene piezas, siempre
incluya el N
o.
de serie de las mismas.
Item
No.
Description
1
Leg Weldment, 27”
1
Leg Weldment, 29”
2
Leg Weldment, with
casters, 27”
2
Leg Weldment, with
casters, 29”
3
Top Frame Weldment
4
Tension Bar
5
Brace
6
Top, 30” x 48”
10
Glide, 1”
11
Rivet, drive, 1/4” dia.x 3/8”
12
Cap Screw, 3/8-24 x 1”
13
Screw, drive, #6 x 1/4”
Item
No.
Description
14
Nut, stop, 3/8-24
15
Serial Plate
17
Cap, tube 1” OD
18 Stool
19
Self-locking Pin
20
Backrest Assembly
21
Backrest
22
Arm, backrest support
24
Stool Assembly
(old-style)
25
Stool (old-style)
26
Screw, #14 x 5/8”
27
Plate, stool
28
Outrigger Leg Assembly
SICO Inc. reserves the right to substitute materials
or make changes, if materials are not available or
such changes improve the product.
SICO Inc. se reserva el derecho a sustituir los
materiales o a realizar modificaciones si los
materiales no están disponibles o si tales
modificaciones mejoran el producto.
Printed in USA (11-04)
Part No. 112668 Rev. E
NOTE: Backrest
Assembly #20 works
only with stool
Assembly #24.
NOTA: el ensamblaje
del respaldo N
o
20
funciona solamente
con el ensamblaje
de la silla N
o
24.
Leg Assembly
Ensamblaje
de las patas
26
21
22
20
25
27
26
24
19
15
13
17
11
19
5
4
6
28
12,14
2
1
10
17
3
14
12
To Assemble the Table
Remove the tension bar (#4) and brace (#5) which are taped to a leg (#1
and #2) for shipment. Pull the legs upright, and attach the tension bar and
brace as shown above.
NOTE:
Level table before tightening fasteners.
Depending on the model ordered, attach the stools (or the stools and
backrests) to the leg assemblies. Refer to the instructions below.
To Attach a Stool
1. Slide the stool (#18) over the top of the stool leg (#1 and #2).
2. Align the holes in the stool hub with the holes in the stool leg.
3. Orient the Self-Locking Pin (#19) with the detent facing up and slide it
through the holes of the stool and stool leg until detent activates.
CAUTION: Self-Locking pin must be installed to prevent excess
wear on stool.
To Attach a Stool and Backrest
1. Slide the backrest assembly (#20) over the stool leg (#1 and #2).
2. Insert the stool plate (#27) through the backrest and over the leg.
3. Hold up the backrest and align the holes in the stool plate and the leg.
4. Orient the Self-Locking Pin (#19) with the detent facing up and slide it
through the holes of the stool plate and stool leg until detent activates.
5. Let the backrest slide down and rest on the pin.
6. Rotate the backrest until its notches rest on the pin.
To reverse the backrest 180
0
, grasp the seatback, pull up about 1”,
then rotate it.
CAUTION: Self-Locking pin must be installed to prevent excess
wear on stool.
See opposite side for these instructions in Spanish.
Vea estas instrucciones en español al dorso.
SICO AMERICA, INC
7525 Cahill Road
Minneapolis, Minnesota 55439, USA
Phone: (800) 424-0796
Website: www.sicoinc.com
18
