SICK UM18-2 Pro Скачать руководство пользователя страница 50

Страница: 50 / 54

Configuration Overview

13.3 Additional settings for all sensors

flashes

Green LED:

Switching between teach-in and

synchronization/multiplex mode

Switch off the supply voltage

Switch on the supply voltage

To change the setting,

apply M at MF for approx. 1 s

Reset to the factory setting

Normal operation mode

Wait approx. 10 s

Wait approx. 3 s until both LEDs

flash simultaneously

Wait approx. 13 s until both

LEDs stop flashing

Further settings

Green LED:

stops flashing

Orange LED:

changes status

Apply M at MF

Orange LED:

on: teach-in

off: synchronization/

multiplex mode

Switch on the supply voltage

Apply M at MF

Before switching off the supply

voltage, disconnect M from MF to

apply the factory setting

Switch off the supply voltage

Содержание UM18-2 Pro























































Результаты поиска

Содержание UM18-2 Pro

Отзывы:

Похожие инструкции для UM18-2 Pro

Бренды по названию

Популярные бренды

SICK UM18-2 Pro, Руководство по эксплуатации

Результаты поиска

Содержание UM18-2 Pro

Отзывы:

Похожие инструкции для UM18-2 Pro

Бренды по названию

Популярные бренды