SICK UM18-2 Pro Скачать руководство пользователя страница 49

Страница: 49 / 54

8014865/ZUJ3/2018-11-29 • © SICK AG • Subject to change without notice 49

Configuration Overview

13.1

Configuration overview for sensors with switching outputs

Position object at

Apply L+ at MF for approx.

3 s until both LEDs flash

simultaneously

Teach-in switching point

(DtO= Distance to Object) –

method A

Both LEDs:

flash

alternately

Apply L+ at MF for approx. 1 s

Teach-in switching point

(DtO= Distance to 8%) –

method B

Both LEDs:

Apply L+ at MF for approx.

3 s until both LEDs flash

again alternately

Teach-in switching window

Both LEDs:

Teach-in background (ObSB

mode = Object between Sensor

and Background)

Both LEDs:

85 %

Set normally closed/

normally open contact

Green LED:

flashes

on: normally open

off: normally closed

Wait approx. 10 s

Normal operation mode

Teach-in switching output

flash

alternately

flash

alternately

flash

alternately

Apply L+ at MF for approx. 1 s

Apply L+ at MF for approx. 10 s

until both LEDs stop flashing

To change the setting, apply

L+ at MF for approx. 1 s

Apply L+ at MF for approx.

3 s until both LEDs flash

simultaneously

Apply L+ at MF for approx.

3 s until both LEDs flash

simultaneously

Apply L+ at MF for approx.

3 s until both LEDs flash

simultaneously

Apply L+ at MF for approx.

13 s until both LEDs flash

alternately

Green LED:

stops flashing

Orange LED:

switches status

flash

alternately

Position object at

Position background at

Default setting:

Normally open contact, switching point (DtO) at maximum operating range

13.2

Configuration overview for sensors with analog outputs

Teach-in analog output scaling

Position object at

Apply L+ at MF for approx. 3 s until

both LEDs flash simultaneously

Apply L+ at MF for approx. 1 s

Set rising/falling

output characteristics

Apply L+ at MF for approx. 13 s

until both LEDs flash alternately

flashes

on: rising,

off: falling output

characteristics

Green LED:

Orange LED:

To change the setting, apply

L+ at MF for approx. 1 s

Wait approx. 10 s

Normal operation mode

Teach-in analog output

Orange LED:

switches status

Green LED:

stops flashing

flash

alternately

Both LEDs:

Position object at

flash

alternately

Both LEDs:

Default setting

: Rising output

characteristics from min. to max.

operating range

Содержание UM18-2 Pro























































Результаты поиска

Содержание UM18-2 Pro

Отзывы:

Похожие инструкции для UM18-2 Pro

Бренды по названию

Популярные бренды

SICK UM18-2 Pro, Руководство по эксплуатации

Результаты поиска

Содержание UM18-2 Pro

Отзывы:

Похожие инструкции для UM18-2 Pro

Бренды по названию

Популярные бренды