SICK UC40 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 46

background image

5

Mounting

5.1

Mounting instructions

•

Observe the technical data.

•

To prevent condensation, avoid exposing the device to rapid changes in tempera‐
ture.

•

The mounting site has to be designed for the weight of the device.

5.2

Arranging multiple devices

5.2.1

Mounting distances

Overview

To use multiple devices, observe the following mounting distances. If you undercut the
specified mounting distance, activate synchronization or multiplex operation.

Mounting distances

Device type

Parallel

Opposite

UC40-112xxx

> 40 cm

> 250 cm

UC40-113xxx

> 110 cm

> 800 cm

UC40-114xxx

> 200 cm

> 1800 cm

5.2.2

Synchronization and multiplex operation

Important notes

NOTE

Synchronization and multiplex operation are not available in IO-Link mode.

Synchronization and multiplex operation

In synchronization or multiplex operation, a maximum of 50 devices can be intercon‐
nected via pin 5 (MF). Synchronization and multiplex operation prevent mutual inter‐
ference of several interconnected devices. The detection area increases to the area
covered by all interconnected devices.

Synchronization mode

In synchronization operation, all devices send and receive the ultrasonic pulses simulta‐
neously. The device detects objects, but does not record the position of the objects.
Synchronization operation starts automatically as soon as the devices are intercon‐
nected via PIN 5 (MF).

Multiplex operation

In multiplex operation, all devices transmit and receive the ultrasonic pulses one after
the other in a defined sequence. The device detects objects and also determines the
position of the objects. To switch to multiplex operation, assign different addresses to
the connected devices via SOPAS ET, IO-Link or the software.

Further topics

•

Activating and deactivating teach-in buttons and synchronization

•

Teaching in several synchronized devices

MOUNTING

5

8027772//2022-08-11 | SICK

O P E R A T I N G I N S T R U C T I O N S | UC40

13

Subject to change without notice

«
...
11
12
13
14
15
...
»

Содержание UC40















































Отзывы:

Нет отзывов

Похожие инструкции для UC40

Бренд: Makita Страницы: 20

Бренд: LAS Страницы: 44

Бренд: LAS Страницы: 24

Бренд: Sami Страницы: 10

Бренд: Tait Страницы: 10

Powersaver Dual Flexi

Бренд: Sangamo Страницы: 2

Бренд: walimex Страницы: 6

Бренд: walimex Страницы: 10

5500DN - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 2

3600B - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 2

PRIME DESIGN VRI3-E-PM11

Бренд: Safe Fleet Страницы: 12

Бренд: Würth Страницы: 2

Бренд: Aptina Страницы: 147

MultiConnect Conduit Series

Бренд: Multitech Страницы: 2

Бренд: Sensit Страницы: 4

Бренд: Whispbar Страницы: 14

Бренд: Manhattan Страницы: 2

Бренд: Kensington Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды