SICK SIM200 Скачать руководство пользователя страница 16

Страница: 16 / 28

Electrical installation

6.1

Important notes

WARNING
Risk of injury and damage caused by electrical current!

Due to equipotential bonding currents, incorrect earthing can lead to the following
dangers and faults: Voltage is applied to the metal housing, cable fires due to cable
shields heating up, the product and other devices become damaged.

■

Generate the same ground potential at all grounding points.

NOTICE

Equipment damage due to incorrect supply voltage!

•

Only operate the device with the specified supply voltage.

•

Please read the notes on electrical installation.

The connection of the network and IO-Link cable of the SIM200 must be voltage-free
(U

= 0 V). The following information must be observed, depending on the connection

type:

■

Even when the wiring is looped through, the total current of the module must not
exceeded 4 A.

■

An incorrect supply voltage may result in damage to the device. Operation is only
permitted in a short-circuit protected system with max. 8 A.

■

Only apply voltage/switch on the voltage supply (U

> 0 V) once all electrical

connections have been established.

6.2

Preparing the electrical installation

To carry out the electrical installation, you will need:

•

Connection cables for the peripheral devices, including the corresponding data
sheets

•

Voltage supply cable

•

If customers assemble the cables: crimping tool, ferrules, soldering iron, and other
installation material

6.3

Assembling the cables (optional)

For a list of cables suitable for use with the device, see:

supportportal.sick.com

or a t

www.sick.com

Customer assembly of the cables is only necessary in special cases. Ensure a sufficient
length of cable is provided, e.g. for strain-relief clamps.

NOTICE
Risk of damage/malfunction due to incorrect PIN assignment

Incorrect wiring of the male connectors/female connectors can lead to damage to or
malfunctions in the system.

■

Observe data sheets provided by the cable manufacturer.

■

Observe the pin assignment.

ELECTRICAL INSTALLATION

O P E R A T I N G I N S T R U C T I O N S | SIM200

8026126//2020-10-15 | SICK

Subject to change without notice

Содержание SIM200





























Результаты поиска

Содержание SIM200

Отзывы:

Похожие инструкции для SIM200

Бренды по названию

Популярные бренды

SICK SIM200, Руководство по эксплуатации

Результаты поиска

Содержание SIM200

Отзывы:

Похожие инструкции для SIM200

Бренды по названию

Популярные бренды