manualshive.com logo in svg

SICK HIPERFACE DSL, Техническая информация, Страница: 26 / 172

Поделиться
Скачать
SICK HIPERFACE DSL Скачать руководство пользователя страница 26

5.3.6

BIGEND signal

bigend

 is a DSL Master digital input.

The byte sequence of the address allocation for registers can be influenced via 

bigend

(see 

chapter 9.5

). The byte sequence is based on 32 bit-wide data words. The selection

influences the allocation independently of the interface block used.

Table 16 below lists the selection options for 

bigend

.

Table 14: bigend selection

Value

Address allocation byte sequence

0

Little endian

1

Big endian

5.4

Test signals

To support development or fault-finding for controllers that have a DSL interface inte‐
grated, the DSL Master supplies some test signals.

5.4.1

SAMPLE signal

sample

 is a DSL Master digital output.

The 

sample 

signal is set at the sampling time point of each bit that is transmitted from

the DSL motor feedback system. It consists of 50 pulses from Channel 1 followed by a
bit pause and 10 pulses from Channel 2 of the motor feedback system.

Figure 12: Sample signal

The 

sample 

signal can be used for eye diagrams to measure time and voltage margins

during signal transmission.

When making the evaluation, signal delays in the DSL Master must be taken into
account. The rising edge of the 

sample 

signal is offset by 40 ns from the line driver

signal. The time delay of the line driver must also be taken into account. Typically this is
13 ns.

5.4.2

ESTIMATOR_ON signal

estimator_on

 is a DSL Master digital output.

The 

estimator_on 

signal is set if some event leads to the transmitted fast position

(see 

chapter 6.3.12

) being invalid and the position estimator supplying the values.

Such events are:

•

The DSL motor feedback system reporting a position error

•

A coding error in transmission of the fast position

•

A check-sum error in transmission of the fast position

•

Realignment from safe to fast - fast position is forced to the safe position value 

•

The protocol is re-synchronizing following a break in the link

5 

INTERFACES

26

T E C H N I C A L   I N F O R M A T I O N | HIPERFACE DSL

®

8017595/ZTW6/2018-01-15 | SICK

Subject to change without notice

Содержание HIPERFACE DSL













































































































































































Отзывы:

Нет отзывов