SICK GM32 Series Скачать руководство пользователя страница 49

Страница: 49 / 80

8012707/ZVF9/V2-1/2019-04 | SICK

O P E R A T I N G I N S T R U C T I O N S | GM32

Subject to change without notice

MAINTENANCE

6.3

Swiveling out and removing the SR-unit

Fig. 31: Swiveling the SR-unit out

For GMP probe: Set the lever on the purge air fixture to the “

Close

” position,

see “Lever of

the locking device (for GMP probe)”, page 36

Open the 4 quick-release fasteners of the SR-unit and swivel the SR-unit out.

To remove the SR-unit:
Hold the SR-unit tight, pull out the hinge pin and take the SR-unit off

6.4

Visual inspection

▸

Check the housings of the SR-unit housing and connection unit for mechanical damage.

▸

Clean the respective housings if contaminated.

▸

Check all cables for damage.
Pay attention to chafe marks and kinks on cable ducts.

▸

Check flanges and screw fittings for firm seating.

WARNING: Damage to eyes through lamp beam

The lamp beam can cause eye damage when the SR-unit is open.

▸

Before opening the SR-unit: Switch the GM32 off at the external main power switch
or wear suitable protective goggles.

WARNING: Danger resulting from escaping gas when the SR-unit is swiveled
out

Excess pressure in the gas duct can cause hot and/or noxious gases to escape when
the SR-unit is swiveled out.

▸

Swivel the SR-unit out only when you have taken suitable safety measures.

▸

For GMP probe: Set the lever on the purge air fixture to the “

Close

” position (

see

“Lever of the locking device (for GMP probe)”, page 36

CAUTION: If the hinge pin has not been correctly inserted, the SR-unit can
drop when swiveled out.

▸

Check that the hinge pin is completely pressed down before swiveling the SR-unit
out,

see “Install the SR-unit:”, page 36

Hinge pin

Hinge

Device flange

SR-unit

NOTE: The SR-unit is heavy

▸

Hold the SR-unit tight when pulling out the pin.

Содержание GM32 Series

















































































Результаты поиска

Содержание GM32 Series

Отзывы:

Похожие инструкции для GM32 Series

Бренды по названию

Популярные бренды

SICK GM32 Series, Руководство по эксплуатации

Результаты поиска

Содержание GM32 Series

Отзывы:

Похожие инструкции для GM32 Series

Бренды по названию

Популярные бренды