SICK GM32 EX Скачать руководство пользователя страница 24

Страница: 24 / 112

3.7.2

Connecting hose SR-unit - junction box

The connecting hose between the SR-unit and the junction box

•

is part of the pressurized enclosure.

•

contains electrical connection cables.

•

is under overpressure.

3.7.3

Intrinsically safe measuring probe (GMP probe)

•

Measuring probe with open measuring gap.

•

Without electronics and therefore intrinsically safe.

•

Protection against contamination: Ex approved purge air unit.

3.8

Ex purge air unit

•

The purge air unit supplies filtered ambient air to the purge air fixtures.

•

Protects the windows of the SR-unit from contamination and high gas tempera‐
tures.

•

A purge air unit for connection to the SR-unit.

•

The purge air is blown into the gas duct through the “flange with tube”.

NOTE

Further information on the purge air unit, see Operating Instructions of the purge air
unit.

DANGER
Risk of explosion by suctioning air from Ex zone 1

The Ex purge air supply may not suction air from Ex zone 1.

Observe zone separation of the purge air supply, air may be suctioned only from
the non-Ex zone or from Ex zone 2.

PRODUCT DESCRIPTION

O P E R A T I N G I N S T R U C T I O N S | GM32-Ex

8015558/YYJ8/V1.7/2016-07 | SICK

Subject to change without notice

Содержание GM32 EX

















































































































Результаты поиска

Содержание GM32 EX

Отзывы:

Похожие инструкции для GM32 EX

Бренды по названию

Популярные бренды

SICK GM32 EX, Руководство по эксплуатации

Результаты поиска

Содержание GM32 EX

Отзывы:

Похожие инструкции для GM32 EX

Бренды по названию

Популярные бренды