background image

Status

Bit

15

14-4

3

2

1

0

Value

Device sta‐
tus:
0 - OK
1 - ERROR

Reserved x/y-velocity

valid
1 - Velocity
is valid
0 - Invalid
(not com‐
putable)

“Status” section

The result data starts at address 0xC0:

Address

Name

#Register

Description / Value

4096

Device Status

1

0 = Device is OK
1 = Maintenance required
3 = Functional Check
2 = Out of Specification
4 = Failure

“Holding registers” register group (read-write)

The following registers are used to configure the sensor via Modbus and can be read
using function code 0x03, written to individually using function code 0x06, or written to
continuously using function code 0x10.

“Commands” section

Address

Name

#Register

Description / Value

96

Set Application name

16

To be set

“Configuration” section

NOTE

Changes become active only after a “power cycle”.

Address

Name

#Register

Description / Value

144

Modbus RTU slave address

1

1 - 247 

(default: 10)

145

Modbus RTU baud rate

1

0: 1,200 bps
1: 2,400 bps
2: 4,800 bps
3: 9,600 bps

4: 19,200 bps (default)

5: 38,400 bps
6: 57,600 bps
7: 115,200 bps

146

Modbus RTU parity setting

1

0: None

1: Even (default)

2: Odd

149

Operating mode

1

0: QR single code
1: DataMatrix single code

2: DataMatrix tag (default)

3: DataMatrix codetape

150

Coordinate system of posi‐
tion data

1

1: Tag centered (default)

2: Sensor centered

151

Module size

2

1.0 mm (default)

(definition SICK MultiCode Tag)

OPERATION 

8

8026282/2021-05-26 | SICK

O P E R A T I N G   I N S T R U C T I O N S | GLS100

37

Subject to change without notice

Содержание GLS100

















































Отзывы: