manualshive.com logo in svg

SICK Flexi IO XTDO1, Руководство по эксплуатации, Страница: 27 / 44

Поделиться
Скачать
SICK Flexi IO XTDO1 Скачать руководство пользователя страница 27

Table 7: I indications (safety capable input)

Display
I

Description

Measures

o

Input is inactive (LOW).

O

 Green

Input is active (HIGH).

Ö

 Green (1 Hz) in sync

with the red PWR indi‐
cation

Input is inactive (LOW) and a recoverable exter‐
nal error is present.

b

Check cabling of the flashing inputs. A short-
circuit to GND or cable break may be present.

Ö

 Green (1 Hz) in sync

with the green PWR
indication

Input is active (HIGH) and a recoverable external
error is present.

b

Check cabling of the flashing inputs. A short-
circuit to 24 V or a cross-circuit to another
signal may be present.

o

 LED off. 

Ö

 LED flashes. 

O

 LED illuminates.

Table 8: Q indications (safety output)

Display
Q

Description

Measures

o

Output is inactive (LOW).

O

 Green

Output is active (HIGH).

Ö

 Green (1 Hz) in sync

with the red PWR indi‐
cation

Output is inactive (LOW) and a recoverable exter‐
nal error is present.

b

Check cabling of the flashing outputs. A short-
circuit to GND or a cross-circuit between out‐
puts may be present.

b

If all indicators of the configured outputs are
flashing, check the supply voltage of the A1
and A2 terminals.

Ö

 Green (1 Hz) in sync

with the green PWR
indication

Output is active (HIGH) and a recoverable exter‐
nal error is present.

b

Check cabling of the flashing outputs. A short-
circuit to 24 V or a cross-circuit between out‐
puts may be present.

o

 LED off. 

Ö

 LED flashes. 

O

 LED illuminates.

Complementary information

The input and output indicators display the status of the terminals with a refresh rate of
approx. 50 ms.

Further topics

•

"Status indicators", page 12

10.2

Possible faults

Important information

NOTE

If a fault response can result in an undesired valid status, you should evaluate the
associated status bits in the logic to initiate suitable measures.

Possible faults and their causes

Table 9: Faults in the logic

Fault

Responses

Causes

Voltage supply A1 / A2
of the main module is
lower than the operat‐
ing range

•

Safety controller switches to the

No supply voltage

 status

•

Voltage supply

 module status bit =

0

•

Status indicators are off

•

Fault in the voltage supply

•

Line break

•

Interruption due to a fuse

TROUBLESHOOTING 

10

8024583/2020-11-10 | SICK

O P E R A T I N G   I N S T R U C T I O N S | Flexi IO XTDO1

27

Subject to change without notice

Содержание Flexi IO XTDO1













































Отзывы:

Нет отзывов