manualshive.com logo in svg

SICK DUSTHUNTER SP100 Ex-2K, Руководство по эксплуатации, Страница: 127 / 130

Поделиться
Скачать
SICK DUSTHUNTER SP100 Ex-2K Скачать руководство пользователя страница 127

127

8024493/AE00/V1-0/2020-09| SICK

O P E R A T I N G   I N S T R U C T I O N S  | DUSTHUNTER SP100 Ex-2K

Subject to change without notice

ACCESSORIES

17

17.4

Optional accessories

17.4.1

Options for MCUDH Ex-3K control unit

The interface module Modbus ASCII/RTU is a retrofit option when an MCUDH Ex-3K without 
integrated module was ordered. The optional interface modules Ethernet Type 2 and 
Modbus TCP/IP of the MCUDH Ex-3K are not to be used in Ex-areas. To use these options, 
an MCUDH Ex-3K with integrated Interface module is required and a signal line must be 
laid from the integrated module in the Ex-area to which the optional modules can be 
connected (

see “Interface module (option) of the MCUDH Ex-3K”, page 59

).

Table 43: Part numbers, optional accessory, MCUDH Ex-3K control unit

17.5

Other accessories

17.5.1

Device check accessories

Table 44: Article numbers, device checking

Name

Part No.

Module, Interface Modbus ASCII/RTU

2048958

Module, Interface Ethernet CoLa-B (remote separate module)

2069666

Module, Interface Modbus TCP/IP (remote separate module)

2069664

Remote display 100, without power supply unit

2117058

Remote display 100, with power supply unit

2117059

SOPAS Service Kit (adapter cable USB-RS485)

2097408

Plug adapter for SOPAS Service Kit

6075779

24 V power supply unit for supplying optional remote modules

6059059

Name

Part No.

DHSP control filter set for linearity testing

2049045

Содержание DUSTHUNTER SP100 Ex-2K



































































































































Отзывы:

Нет отзывов