manualshive.com logo in svg

SICK DT50-2 Pro, Руководство по эксплуатации


Поделиться
Скачать
background image

8

Troubleshooting

Possible faults and rectification measures are described in the table below. In case
of faults that cannot be rectified using the information below, please contact the
manufacturer. See the back page for your agency.

General faults, warnings and errors

General faults are subdivided into warnings and errors. Current measured values con‐
tinue being output when there are warnings; measurement is no longer possible when
there are faults. Warnings and errors are signaled by the 

Status

 LED. The 

Power

 LED

signals that the sensor is connected to the power supply.

8.1

Detecting and displaying errors

In addition to measurement errors (

see "Behavior if no measurement is possible

(NoMeasurement)", page 65

), the sensor can also detect and display other errors.

These are output by the display, Sopas ET or IO-Link.

Error memory

The sensor has an error memory where internal error states of the sensor are recorded.
The last error to have occurred is always saved. The contents of the error memory
are retained when the sensor is switched off and when the “Restore Factory Settings”
function is used.

Possible errors

Table 16: Explanation of the error code

Error code

Meaning

Countermeasure(s)

OK

No error

--

ERR010

Operating temperature under‐
shot

Check the ambient tempera‐
ture and raise it, if necessary

WRN011, ERR011

Operating temperature
exceeded

Check the ambient tempera‐
ture and lower it, if necessary

WRN045, WRN046, ERR045,
ERR046

Electrical fault

Check the electrical environ‐
ment and improve it, if neces‐
sary (stability, power supply,
EMC influences)

If a different message is output, please contact the manufacturer's technical support.

8.1.1

Operating example via display: Display device status (“Status”)

Display device status (“Status”)

Operating example or steps:

RUN mode

 → Q

1

 Output

/

 to → Info

 → FW Version
/

 to → Status

 → Status is displayed
 to → RUN mode

Necessary default settings:

User level = Advanced

Factory setting:

OK

8 

TROUBLESHOOTING

74

O P E R A T I N G   I N S T R U C T I O N S | DT50-2 Pro

8017154/1AVV/2021-03-24 | SICK

Subject to change without notice

Содержание DT50-2 Pro





































































































Отзывы:

Нет отзывов

Похожие инструкции для DT50-2 Pro

Panasonic KX-FLM551 Schematic Diagrams preview
KX-FLM551
Бренд: Panasonic Страницы: 2
3M Versaflo M Series User Instructions preview
Versaflo M Series
Бренд: 3M Страницы: 27
3M Speedglas 9100 Series User Instructions preview
Speedglas 9100 Series
Бренд: 3M Страницы: 64
3M Speedglas 9100 Series Quick Start Manual preview
Speedglas 9100 Series
Бренд: 3M Страницы: 2
3M Speedglas 9100 Manual preview
Speedglas 9100
Бренд: 3M Страницы: 2
3M Speedglas 9002NC User Manual preview
Speedglas 9002NC
Бренд: 3M Страницы: 52
3M L-905 Disassembly preview
L-905
Бренд: 3M Страницы: 5
3M Speedglas 9100 FX Series Care & Maintenance preview
Speedglas 9100 FX Series
Бренд: 3M Страницы: 2
Hama Bike Operating Instructions Manual preview
Bike
Бренд: Hama Страницы: 22
Camcar 40104 Mounting Instructions preview
40104
Бренд: Camcar Страницы: 6
VEAP SHIELD UNITED FT Series Mounting Instruction preview
FT Series
Бренд: VEAP SHIELD UNITED Страницы: 3
Kargo Master 80070 Assembly Lnstructions preview
80070
Бренд: Kargo Master Страницы: 13
Kargo Master 4A96L Installation Manual preview
4A96L
Бренд: Kargo Master Страницы: 21
Kargo Master 40201 Installation Manual preview
40201
Бренд: Kargo Master Страницы: 4
Karel MS48IP Technical Reference And Installation Manual preview
MS48IP
Бренд: Karel Страницы: 56
Paradyne COMSPHERE 6800 Series Installation And Enabling/Disabling Instructions preview
COMSPHERE 6800 Series
Бренд: Paradyne Страницы: 7
PASCO PS-3201 Reference Manual preview
PS-3201
Бренд: PASCO Страницы: 8
Radio Shack XMODS Custom RC Owner'S Manual preview
XMODS Custom RC
Бренд: Radio Shack Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды