manualshive.com logo in svg

SICK DT50-2 Pro, Руководство по эксплуатации


Поделиться
Скачать
background image

Table 7: Process data formats

No.

Description

Comments

1

Distance (14-bit) + Status Q

1

 + Status Q

2

2

Level (14-bit) + Status signal level warning (SLW) + Status alarm

3

Distance (16-bit)

Factory setting

4

Distance (14-bit) + Signal quality (2-bit)

5

Timer (16-bit)

6

Timer (14-bit) + Status Q

1

 + Status Q

2

7

Shape match (7-bit) + Shape count (7-bit) + Status Q

1

 + Status

Q

2

6.3.4.2

Device data

In addition to the process data, device data (parameters, identification data and diag‐
nostic information) can be transmitted to and from the sensor. To use this function, a
sensor-specific device description file (IODD) is needed in the IO-Link master.

A download package with the IODD and supplementary documentation is available at

www.sick.com/Dx50-2

.

The volume of device data that is accessible via IO-Link essentially corresponds to the
data displayed in SOPAS ET.

6.3.5

Operation via multifunctional input (MF)

You can also use the multifunctional input (MF) to configure parameters and teach in
for all DT50-2 Pro versions. More information about operation via multifunctional input
(MF) 

see "Multifunctional input (“MF Input”)", page 57

.

6.4

Description of operation

6.4.1

Switching mode for Q

1

 (“ModeQ

1

”)

The output Q

1

 of DT50-2 Pro provides the following switching modes:

■

Distance to object or single switching point (“DtO (1point)”)

■

Switching window (“Window”)

■

Object between sensor and background (“ObSB (Background)”)

■

Shape comparison (“Shape”, Advanced user level only)

■

Fault output (“Alarm”, Advanced user level only)

■

Signal level warning (“SLWarning”, Advanced user level only)

These are described in detail in the following.

6.4.1.1

“Distance to object” or single switching point (“DtO (1point)”) switching mode

6.4.1.1.1

Description

Output of a signal if the measured distance value has undershot (High Active) or
exceeded (Low Active) the switching point.

6 

OPERATION

22

O P E R A T I N G   I N S T R U C T I O N S | DT50-2 Pro

8017154/1AVV/2021-03-24 | SICK

Subject to change without notice

Содержание DT50-2 Pro





































































































Отзывы:

Нет отзывов

Похожие инструкции для DT50-2 Pro

ECO Sensors C-21 Instructions For Use preview
C-21
Бренд: ECO Sensors Страницы: 2
EarthX ETX900-TSO Instructions Manual preview
ETX900-TSO
Бренд: EarthX Страницы: 17
EarthX ETX Series Installation & Maintenance Manual preview
ETX Series
Бренд: EarthX Страницы: 23
Wallenstein GE Series Operator'S Manual preview
GE Series
Бренд: Wallenstein Страницы: 48
Olympus FS-1 Instructions preview
FS-1
Бренд: Olympus Страницы: 2
S&B Filters 76-6000 Installation Instructions Manual preview
76-6000
Бренд: S&B Filters Страницы: 7
SAGEMCOM Fast PLUG 500 premium Quick Installation Manual preview
Fast PLUG 500 premium
Бренд: SAGEMCOM Страницы: 2
Yakima K1188 Instructions Manual preview
K1188
Бренд: Yakima Страницы: 12
JEHNERT SOUND DESIGN 65400 Assembly Instruction Manual preview
65400
Бренд: JEHNERT SOUND DESIGN Страницы: 8
Rainbow Experience Series Installation Manual preview
Experience Series
Бренд: Rainbow Страницы: 19
Yakima K1006 Instructions Manual preview
K1006
Бренд: Yakima Страницы: 12
Warmington Southern Series Quick Start Manual preview
Southern Series
Бренд: Warmington Страницы: 2
Camcar 40061 Fe Mounting Instructions preview
40061 Fe
Бренд: Camcar Страницы: 2
R&G LP0273 Fitting Instructions Manual preview
LP0273
Бренд: R&G Страницы: 22
R&G ECC0337R Fitting Instructions Manual preview
ECC0337R
Бренд: R&G Страницы: 8
DEFA WarmUp 411702 Fitting Instructions Manual preview
WarmUp 411702
Бренд: DEFA Страницы: 9
rough country Slim Line LED Light Grille Kit Manual preview
Slim Line LED Light Grille Kit
Бренд: rough country Страницы: 8
Crestron FT2A-PWR-IT Series Quick Start preview
FT2A-PWR-IT Series
Бренд: Crestron Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды