SICK D 35 Series Скачать руководство пользователя страница 9

Страница: 9 / 68

8014868/YIF1/2020-10-19 • © SICK AG • Subject to change without notice 9

General information

1.2

Explanation of symbols

Warnings

Warnings in these operating instructions are labeled with symbols. The

warnings are introduced by signal words that indicate the extent of the

danger.
These warnings must be observed at all times and care must be taken to

avoid accidents, personal injury, and material damage.

DANGER!

… indicates a situation of imminent danger, which will

lead to a fatality or serious injuries if not prevented.

WARNING!

… indicates a potentially dangerous situation, which may

lead to a fatality or serious injuries if not prevented.

CAUTION!

… indicates a potentially dangerous situation, which may

lead to minor/slight injuries if not prevented.

IMPORTANT!

… indicates a possible hazardous situation which may

lead to physical damage if it is not avoided.

Tips and recommendations

NOTE!
… highlights useful tips and recommendations as well as

information for efficient and trouble-free operation.

Содержание D 35 Series





































































Результаты поиска

Содержание D 35 Series

Отзывы:

Похожие инструкции для D 35 Series

Бренды по названию

Популярные бренды

SICK D 35 Series, Руководство по эксплуатации

Результаты поиска

Содержание D 35 Series

Отзывы:

Похожие инструкции для D 35 Series

Бренды по названию

Популярные бренды