SICK D 35 Series Скачать руководство пользователя страница 36

Страница: 36 / 68

Commissioning

8.5

Expert mode

Use expert mode to set the following functions:
• Function for multifunction input MF:

External teach (factory setting), laser off, multifunctional input MF deac

tivated

• Level for multifunction input MF:

High active (factory setting), Low active

• For DT35/DL35 distance sensors:

Output behavior for output 2:

4 … 20 mA (factory setting), 0 … 10 V, switching output Q2

Description

Active LED

LED slow … fast

Function for multi-

function input

Q1 near

• LED

slow … fast

flashes 1 x:

external teach

• LED

slow … fast

flashes 2 x:

laser off

• LED

slow … fast

flashes 3 x:

Multifunctional input MF deactivated

Level for multi-

function input

Q1 far

• LED

slow … fast

flashes 1 x:

low active

• LED

slow … fast

flashes 2 x: high

active

Output behavior

for output Q2

Q2 near

• LED

slow … fast

flashes 1 x: 4 …

20 mA

• LED

slow … fast

flashes 2 x: 0 …

10 V

• LED

slow … fast

flashes 3 x: Switch

ing output

1) For DT35/DL35 distance sensors only

Table 8:

Overview of expert mode

Output: The output Q2 is to be set to 0 … 10 V.
1. From operating mode only: Press

select

and

set

pushbuttons simulta-

neously for longer than 10 seconds. The LED

near

lights up and the

LED

slow

…

fast

flashes cyclically according to the previous setting.

2. Keep pressing the pushbutton until the LED

Q2 near

lights up.

3. Keep pressing the

set

pushbutton until the desired option has been

set.
• LED

slow … fast

flashes 1 x: 4 … 20 mA

• LED

slow … fast

flashes 2 x: 0 … 10 V

• LED

slow … fast

flashes 3 x: switching output.

4. In order to leave expert mode, press the

select

and

set

pushbuttons

for longer than 10 seconds or wait 5 minutes without pushing the

pushbuttons.

Содержание D 35 Series





































































Результаты поиска

Содержание D 35 Series

Отзывы:

Похожие инструкции для D 35 Series

Бренды по названию

Популярные бренды

SICK D 35 Series, Руководство по эксплуатации

Результаты поиска

Содержание D 35 Series

Отзывы:

Похожие инструкции для D 35 Series

Бренды по названию

Популярные бренды