SICK D 35 Series Скачать руководство пользователя страница 18

Страница: 18 / 68

Design and function

Q1 and Q2 status LEDs (continued)

LED

Description

Q1 and Q2 in align-

ment mode

Alignment quality indicator (IR models only)
•

Slow flashing (approx. 1 Hz): poor alignment quality

•

Rapid flashing (approx. 15 Hz): good alignment quality

Table 2:

Q1 and Q2 status LEDs

Status indicator LED

LED

Description

Run

Operating indicator
• Rear LED green/front LED orange: Supply voltage pres-

ent

•

LED off: Supply voltage off

Table 3:

Status indicator LED

Teach-in LEDs

(continued on next page)

LED

Description

Q1 near, Q1 far,

Q2 near, Q2 far,

in teach mode

• Perform one-point or window teach.
• One of the LEDs lights up: Teach can be performed.
•

One of the LEDs flashes: Fine teach can be performed.

Q1 near + Q1 far

(ObSB)

in teach mode

Teach in ObSB or background for switching output Q1.
• Both LEDs light up: Teach can be performed.
•

Both LEDs flash: Fine teach can be performed.

Q2 near + Q2 far

(ObSB)

in teach mode

Teach in ObSB or background for switching output Q2.
• Both LEDs light up: Teach can be performed.
•

Both LEDs flash: Fine teach can be performed.

slow … fast

in teach mode

Set speed. "Slow … fast" LED flashes cyclically:

• 1 x: Super-slow
• 2 x: Slow
• 3 x: Medium
• 4 x: Fast
• 5 x: Super-fast
"Slow … fast" LED lights up continuously:
• Expert or expert setting, adjustable only via IO-Link

→

See Chapter 9.3.3 on page 43

Q1 near, Q1 far,

Q2 near, Q2 far,

slow … fast

in alignment mode

Alignment quality indicator (IR models only)
• The greater the number of LEDs that light up, the better

the teach-in quality.

Содержание D 35 Series





































































Результаты поиска

Содержание D 35 Series

Отзывы:

Похожие инструкции для D 35 Series

Бренды по названию

Популярные бренды

SICK D 35 Series, Руководство по эксплуатации

Результаты поиска

Содержание D 35 Series

Отзывы:

Похожие инструкции для D 35 Series

Бренды по названию

Популярные бренды