SICK Bulkscan Скачать руководство пользователя страница 29

Страница: 29 / 112

O P E R AT I N G I N S T R U C T I O N S | Bulkscan®

8014829/ZV98/2018-05-07| S I C K

Subject to change without notice

2 9

CONFIGURABLE FUNCTIONS

4.15.1

Ethernet interface

The Ethernet interface has a data transmission rate of 10/100 Mbit/s. The interface is

a TCP/IP interface supporting full duplex and half duplex.

The Ethernet interface allows the configuration of the Bulkscan® as well as the output

of measured values.

If your network uses static IP addresses, then you must adapt the configuration of the

Ethernet interface so that a connected PC (client) can communicate with the Bulk-

scan® via Ethernet. If you are unsure about the correct Ethernet configuration, please

contact your network administrator.

Network

tab,

Interfaces, Ethernet

If you change the parameters for the interface via which you are connected to the sen-

sor, the connection to the sensor will be lost. You must re-establish the connection (see

"7.1.2 Establishing communication with the Bulkscan®“ on page 61).
To connect the electrical interface, (see "6.2.2 Ethernet interface connection“ on page

47).

4.15.2

Serial host interface

The Serial host interface is an RS-232/RS-422 interface (RS-422 only Bulkscan®

LMS511). The host interface permits the configuration of the Bulkscan® LMS511 and

Bulkscan® LMS111 and limited output of measured values.

The interface parameters are freely configurable.

Network

tab,

Interfaces, Serial, Serial Host Interface

group.

The factory setting for the host interface is as follows:

• 57,600 baud

• 8 data bits

• 1 stop bit

• No parity bit

The data transmission rate of the RS-232/RS-422 interfaces (RS-422 only Bulkscan®

LMS511) is limited to 57,600 baud. Therefore these interfaces are not suitable for

transmitting scan data in real time.
If you change the parameters for the interface via which you are connected to the sen-

sor, the connection to the sensor will be lost. You must re-establish the connection (see

"7.1.2 Establishing communication with the Bulkscan®“ on page 61).
To connect the electrical interface, (see "6.2.4 Serial interface connection of Bullk-

scan® LMS511“ on page 48).

4.15.3

Serial auxiliary interface/USB on Bulkscan® LMS511

The Mini-USB Interface permits the direct configuration of the Bulkscan®.

•

Configuration via USB is only possible if you have installed the USB driver during the

installation of the SOPAS configuration software. This is the case with the default

installation.

• Parameters can then also be changed via USB, if the Bulkscan® is connected to a

host via another interface. Only the changes last saved in the sensor are retained.

Note

Содержание Bulkscan

















































































































Результаты поиска

Содержание Bulkscan

Отзывы:

Похожие инструкции для Bulkscan

Бренды по названию

Популярные бренды

SICK Bulkscan, Руководство по эксплуатации

Результаты поиска

Содержание Bulkscan

Отзывы:

Похожие инструкции для Bulkscan

Бренды по названию

Популярные бренды