siat ProWrap 16_H_FM Скачать руководство пользователя страница 78

Страница: 78 / 104

Control system

IDM 510-140-0

English language

Operation and maintenance manual

Language selection mode

The figure shows the points of intervention and the description shows the

procedures to be adopted.

Display the LANGUAGES screen

(6)

(See “Operator inter-

face navigation diagram (standard)”).

Touch the icon that corresponds to the desired language.

– The text that is to be found in all screens will immediately

update to the selected language.

Password entering mode

The figure shows the points of intervention and

the description shows the procedures to be

adopted.
1.

Touch the icon

Press the field

and enter the operator ID.

Press the field

and enter the password.

Press the key

to confirm.

Any time you deactivate the power supply of the

machine, you must repeat the procedures to en-

ter the password.

–

To prevent operations by unauthorised peo-

ple, cancel the password as specified.

Touch the icon

Press the key

to confirm.

Содержание ProWrap 16_H_FM









































































































Результаты поиска

Содержание ProWrap 16_H_FM

Отзывы:

Похожие инструкции для ProWrap 16_H_FM

Бренды по названию

Популярные бренды

siat ProWrap 16_H_FM, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание ProWrap 16_H_FM

Отзывы:

Похожие инструкции для ProWrap 16_H_FM

Бренды по названию

Популярные бренды