__p
3. Unfasten the rack mount screws and remove the rack.
XC60J Quick Guide【English】
Jumper Settings
Motherboard Illustration
53R-XC60J3-H001
Front Panel
Back Panel
F1. USB 3.0 port
F2. USB 2.0 port
F3. Mic-in
F4. Headphone
F5. Power switch / Power LED
F6. HDD LED
F7. COM6 port (RS232)
F8. COM7 port (RS232)
F9. COM8 port (RS232)
B1. DC power port
B2. LAN port
B3. USB 2.0 port
B4. Kensington
®
lock port
B5. D-Sub (VGA) port
B6. HDMI port
B7. COM2 port (RS232)
B8. COM1 port (RS232/422/485)
B9. COM4 port (RS232)
B10. COM3 port (RS232)
B11. Clear CMOS
B12. COM5 port (RS232)
Safety Information
CAUTION
Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended
by Shuttle. Dispose of used batteries according to the manufacturer's instructions.
1. Unscrew the two thumbscrews of the chassis cover.
3. Untie all cables for easier installation.
5. Connect the Serial ATA and power cables to the HDD or SSD.
Serial ATA cable
Serial ATA power cable
1. Replace the cover and refasten the thumbscrews.
D.
Complete
Please press the "Del" key while booting to enter BIOS. Here,
please load the optimised BIOS settings.
2. Complete.
2. Slide the cover backwards and upwards.
4. Place the HDD or SSD in the rack and secure with the four screws.
6. Slide the rack in the chassis and refasten the
four screws.
1. Locate the SO-DIMM slot on the mainboard.
2. Align the notch of the memory module with the one of the memory slot.
3. Gently insert the module into the slot in a 45-degree angle.
4. Carefully push down the memory module until it snaps into the locking
mechanism.
5. Repeat the above steps to install additional memory modules,
if required.
Purse lock
Read the following precautions before setting up a Shuttle XPC.
Notch
SO-DIMM slot
3
45-degree
angle
1
2
Latch
Latch
J3
Power header (SW2)
Fan connector (FAN1)
J8
1=HDLEDPWR
2=PWR_LED
3=SATALED
4=GND
5=RST_SW
6=PWR_SW
7=GND
8=GND
9=NULL 10=NA
1=GND
2=+12V
3=SPEED_SENSE
4=PWM_CTRL
SATA power connector
(+5V)(PW2)
J6
SATA power connector
(+12V)(PW1)
J7
1=GND
2=GND
3=+5V
4=+5V
1=GND
2=NC
3=+12V
B1
B6
B11
B3
B8
B10
F1
F2
F4
F3
F2
F5
F6
B4
B5
B12
B2
B7
B9
F7
F8
F9
COM port header (COM5,COM6,COM7,COM8)
CPU
DDR3L SODIMM slot-DIMMB1
LAN (x1) & USB 2.0 (x2) port
SATA connector-SATA1
D-Sub (VGA) & HDMI port
Audio connector-AUDIO1
J3
J8
DC power port
SATA power connector
(+5V)-PW2
Fan connector-FAN1
M.2 2230 A,E key slot
Clear CMOS button
LPC header-LPC1
Front USB 3.0 header-USB4
SATA power connector
(+12V)-PW1
Power header-SW2
J5
COM (x2) port
J7
J1
J10
COM port header-COM6
COM port header-COM7
COM port header-COM8
COM port header-COM5
COM power switch-JP7
COM power switch-JP8
COM power switch-JP9
COM power switch-JP2
Battery connector-CN1
J6
J2
Front USB 2.0 header-USB2
J9
USB 2.0 connector-USB3
AC back auto power on-JP5
J4
M.2 2242/2260/2280 M key slot
DDR3L SODIMM slot-DIMMA1
COM (x2) port
J11
J13
J13
J13
J12
J12
J12
J12
J13
Audio connector (AUDIO1)
J2
1=MIC_L
2=AGND
3=MIC_R
4=FRONT-JD
5=HP_R_C
6=MIC-JD
7=SENSE B 8=NULL
9=HP_L_C
10=HP-JD
LPC header (LPC1)
J1
1=LPC_24M
2=GND
3=LFRAME
4=NULL
5=SIORST-
6=NC
7=LAD3
8=LAD2
9=+3.3V
10=LAD1
11=LAD0 12=GND
13=LPC_48M 14=PCH_PME-
15=+3.3VS 16=SERIRQ
17=GND 18=CLKRUN_NC
19=PD#_NC 20=SUS_CLK_TPM
20
18
16
14
12
10
8
6
4
2
19
17
15
13
11
9
7
5
3
1
Battery connector (CN1)
1=V_BAT
2=GND
J4
AC back auto power on (JP5)
1=PWRSW-
2=GND
1
2
SHORT (Disabled)
OPEN (Enabled)
Front USB 3.0 header (USB4)
J5
1=USB30_PWR
2=USB30_PWR
3=USB30_PWR
4=USB30_PWR
5=U3_RX0N
6=U3_RX0P
7=GND
8=GND
9=U3_TX0N
10=U3_TX0P 11=GND
12=GND
13=USB0_N 14=USB0_P 15=USB30_PWR
16=USB30_PWR 17=USB30_PWR 18=USB30_PWR
19=U3_RX1N 20=U3_RX1P 21=GND
22=GND
23=U3_TX1N 24=U3_TX1P
25=GND 26=GND 27=USB2_N
28=USB2_P 29=GND
30=GND
Front USB 2.0 header (USB2)
1=USB_PWR
2=USB_PWR
3=USB4_N
4=USB3_N
5=USB4_P
6=USB3_P
7=GND
8=GND
9=NC
10=GND
J9
J11
USB 2.0 connector (USB3)
1=GND
2=USB1_P
3=USB1_N
4=USB_PWR
J10
J12
A. Begin Installation
For safety reasons, please ensure that the power cord is
disconnected before opening the case.
B. Memory Module Installation
L
The product’s colour and specifications may vary from the actually shipping product.
This mainboard does only support 1.35V DDR3L SO-DIMM
memory modules.
C. Component Installation
1. As shown, unfasten the screw first.
2. Install the M.2 device into the M.2 slot and secure with the screw.
COM power switch (JP7,JP8,JP9,JP2) (DEFAULT=SHORT 1-2,3-4) RI(NA)
J13
1=DCD
2=RX
3=TX
4=DTR
5=GND
6=DSR
7=RTS
8=CTS
9=RI(NA) 10=N/C
COM1_2(Down) & COM1_2(Up) POWER SWITCH : JP7
Support RS232 Back panel
Independent External Power 12V / 5V
JUMP1 Connector Pin 1 and Pin 2 = RI1 Signal.
JUMP2 Connector Pin 3 and Pin 4 = RI2 Signal.
IF JUMP1 Connector Pin 5 and Pin 7 = RI1 is VCC
IF JUMP2 Connector Pin 6 and Pin 8 = RI2 is VCC
IF JUMP1 Connector Pin 7 and Pin 9 = RI1 is 12V
IF JUMP2 Connector Pin 8 and Pin 10 = RI2 is 12V
1=-XRI1(NA)
2=COM_-XRI1(NA)
3=-XRI2(NA)
4=COM_-XRI2(NA)
5=+5V
6=+5V
7=COM1_PWR 8=COM2_PWR
9=+12V 10=+12V
9 7 5
3 1
10
8 6
4 2
JP7
COM3_4(Down) & COM3_4(Up) POWER SWITCH : JP8
Support RS232 Back panel
Independent External Power 12V / 5V
JUMP1 Connector Pin 1 and Pin 2 = RI3 Signal.
JUMP2 Connector Pin 3 and Pin 4 = RI4 Signal.
IF JUMP1 Connector Pin 5 and Pin 7 = RI3 is VCC
IF JUMP2 Connector Pin 6 and Pin 8 = RI4 is VCC
IF JUMP1 Connector Pin 7 and Pin 9 = RI3 is 12V
IF JUMP2 Connector Pin 8 and Pin 10 = RI4 is 12V
1=-XRI3(NA)
2=COM_-XRI3(NA)
3=-XRI4(NA)
4=COM_-XRI4(NA)
5=+5V
6=+5V
7=COM3_PWR 8=COM4_PWR
9=+12V 10=+12V
9 7 5
3 1
10
8 6
4 2
JP8
COM5 & COM6 POWER SWITCH : JP9
Support RS232 Back panel
Independent External Power 12V / 5V
JUMP1 Connector Pin 1 and Pin 2 = RI5 Signal.
JUMP2 Connector Pin 3 and Pin 4 = RI6 Signal.
IF JUMP1 Connector Pin 5 and Pin 7 = RI5 is VCC
IF JUMP2 Connector Pin 6 and Pin 8 = RI6 is VCC
IF JUMP1 Connector Pin 7 and Pin 9 = RI5 is 12V
IF JUMP2 Connector Pin 8 and Pin 10 = RI6 is 12V
1=-XRI5(NA)
2=COM_-XRI5(NA)
3=-XRI6(NA)
4=COM_-XRI6(NA)
5=+5V
6=+5V
7=COM5_PWR 8=COM6_PWR
9=+12V 10=+12V
9 7 5
3 1
10
8 6
4 2
JP9
COM7 & COM8 POWER SWITCH : JP2
Support RS232 Back panel
Independent External Power 12V / 5V
JUMP1 Connector Pin 1 and Pin 2 = RI7 Signal.
JUMP2 Connector Pin 3 and Pin 4 = RI8 Signal.
IF JUMP1 Connector Pin 5 and Pin 7 = RI7 is VCC
IF JUMP2 Connector Pin 6 and Pin 8 = RI8 is VCC
IF JUMP1 Connector Pin 7 and Pin 9 = RI7 is 12V
IF JUMP2 Connector Pin 8 and Pin 10 = RI8 is 12V
1=-XRI7(NA)
2=COM_-XRI7(NA)
3=-XRI8(NA)
4=COM_-XRI8(NA)
5=+5V
6=+5V
7=COM7_PWR 8=COM8_PWR
9=+12V 10=+12V
9 7 5
3 1
10
8 6
4 2
JP2
9 7 5 3 1
10 8 6 4 2
1 3 5 7 9
2 4 6 8 10
4
3
2
1
9
7
5
3
1
10
8
6
4
2
4 3 2 1
1
2
3
4
3
2
1
1 2
9 7 5 3 1
10 8 6 4 2
1
30
E
For the 2.5" HDD/SSD
E
For the 3.5" HDD/SSD
E
For the 2.5" HDD/SSD
E
For the 3.5" HDD/SSD
2
1
DIMMA1
DIMMB1
M.2 2230 A,E key slot
M.2 2242/2260/2280 M key slot
HDD rack
E
For the 3.5" HDD/SSD
E
For the 2.5" HDD/SSD
COM PORT (COM1_2, COM3_4)
1 2 3 4 5
6 7 8 9
1=DCD_485TX- 6=DSR
2=R
7=RTS
3=T
8=CTS
4=DTR_422RX- 9=RI(NA)
5=GND 10=N/C
RS232/422/485:
COM1_2 (Down)
1=DCD
6=DSR
2=RX
7=RTS
3=TX
8=CTS
4=DTR
9=RI(NA)
5=GND 10=N/C
Only RS232:
COM1_2 (UP) and COM3_4
