Shrinkfast 975 страница 38 Скачать руководство пользователя

Страница: 38 / 40

Problem

Probable Cause

Remedy

Gun will not ignite

The POL excess check

valve has not fully opened.

Turn on propane tank valve and wait

10 seconds or until the needle on the
regulator has reached the factory setting
of 22 PSI. An audible “click” will be
heard when the hose has fully
pressurized with gas.

Clogged orifice

Remove and clean with compressed air.

Clogged fuel line

Remove and clean with compressed air.

Clogged pump body

Remove and clean with compressed air.

Clogged hose assembly

Disconnect and clean with
compressed air.

Combustor turns
glowing red

Low pressure from tank

Increase pressure from tank or
replace tank.

Extremely large flame

Wrong fuel type

Do not use a fork truck tank; only

vapor withdrawal tanks like a BBQ tank.

Tank, regulator or hose

fittings have iced up.

Low pressure from tank

Increase pressure on regulator or
change to a new tank.

Содержание 975









































Результаты поиска

Содержание 975

Отзывы:

Похожие инструкции для 975

Бренды по названию

Популярные бренды

Shrinkfast 975, Руководство по эксплуатации, техническому обслуживанию и каталог запасных частей

Результаты поиска

Содержание 975

Отзывы:

Похожие инструкции для 975

Бренды по названию

Популярные бренды