background image

- 5 - 

Precautions for the use of an inverter to operate the blower. 

1)   The standard motor may not be used for the operation in some cases as shown below. 

    ・

  In the case of no margin for temperature rise in the motor 

2)  At factory shipment, the setting of a commercial inverter is not suitable for the blower. 

 

  Change the following values at least. 

    ・

Base frequency: Adjust to the rated frequency of the blower (50 Hz or 60 Hz). 

    ・

Highest frequency: Adjust to the rated frequency of the blower. 

    ・

Maximum output voltage: Adjust to the rated voltage of the motor. 

    ・

Upper-limit frequency: Highest frequency: Adjust to the rated frequency of the blower. 

    ・

Lower-limit frequency: 25 to 30 Hz (based on the cooling characteristics of the motor). 

    ・

V/f characteristics: Change to square reduction torque. 

    ・

Acceleration time: 30 to 60 sec. or more If the acceleration time is short, an over-current error   

may occur. 

    ・

Deceleration time: 30 to 60 sec. or more If the decceleration time is short, a regenerative current   

error may occur. 

3

) 

Other precautions 

    ・

  Vibrations of components (belt, casing, etc.) making up the blower may increase at a specific   

frequency. If the increase in vibration cannot be eliminated even after other set values are   
changed, a resonance point may be causing it. In such a case, set the jump frequency to   
prevent the increase in frequency. 

    ・

If the blower is installed on a vibration isolation table (rubber, spring, etc.), a decrease in   

frequency may become a resonance frequency. In such a case, set the jump frequency to prevent   
this symptom (otherwise, the blower and motor are individually affected). 

    ・

If the carrier frequency is set higher, current leakage may increase, and the earth leakage   

breaker may be activated. 

    ・

Do not use the inverter output power for applications other than electric motors. 

 
For details, see “Use of inverter (frequency converter)” on page 20. 

Содержание KAIRYU

















Отзывы: