Shop fox SHOP FOX W1669 страница 42 Скачать руководство пользователя

Страница: 42 / 60

-40-

Model W1669/W1670 (For Machines Mfd. Since 04/18)

The drill press comes fitted with a depth stop to use

when drilling multiple holes at the same depth. The scale

on this depth stop can be calibrated if it ever becomes

incorrect.

To calibrate the depth stop, do these steps:

Loosen the return height nut and calibration nut

shown in

Figure

Use the calibration nut to zero the depth stop scale

with the stop bracket.

Hold the depth stop at zero, and tighten the return

height nut to hold the depth stop in position.

Test the depth stop by measuring how far the spindle

actually moves with respect to where you set the

depth stop.

Calibrating.Depth.Stop

Figure.39.

Depth-stop components.

Stop

Bracket

Calibration

Nut

The tension of the spindle return spring makes the spindle

automatically return to the top (starting) position when the

downfeed handle is released. This spring is pre-adjusted at

the factory, and typically will never need further adjustment

during the life of the drill press. However, additional tension

can be applied if the spindle stops automatically returning to

the top position.

To.adjust.the.spindle.return.spring.tension,.do.these.

steps:

DISCONNECT THE MACHINE FROM POWER!

2...

Wipe off any oil on the spring-lock cover so it will

not slip when you hold the cover from spinning (see

Figure.40

Adjusting.Spindle.Return.

Spring.Tension

Figure.40..

Spindle return spring

components.

Spring

Lock

Cover

Locking Lug

Wear.safety.goggles.and.heavy.leather.

gloves. when. adjusting. the. spindle.

return.spring..Serious.injury.may.occur.

if.this.warning.is.ignored!

Cover

Nut

Jam

Nut

Return

Height

Nut

Содержание SHOP FOX W1669





























































Результаты поиска

Содержание SHOP FOX W1669

Отзывы:

Похожие инструкции для SHOP FOX W1669

Бренды по названию

Популярные бренды

Shop fox SHOP FOX W1669, Руководство пользователя

Результаты поиска

Содержание SHOP FOX W1669

Отзывы:

Похожие инструкции для SHOP FOX W1669

Бренды по названию

Популярные бренды