Shively Labs 6822 Скачать руководство пользователя страница 45

Страница: 45 / 78

Connecting the Antenna (8-bay)

Connect the tower
transmission line.

NOTE

You may need to provide a coax adapter between your transmission line

and the antenna components.

a. The antenna system is not pressurized, but the tower transmission line may

be. If necessary, provide a gas stop between the tower transmission line and

the system input (power divider input, or transformer input if applicable).

b. Coat the O-ring (43 or 54, as applicable) lightly with O-Lube (supplied with

the antenna), then install it in the O-ring groove in the flange.

c. Using the flange hardware kit (42 or 53, as applicable), attach the tower

transmission cable to the power divider (or transformer) input. Tighten in

accordance with

Table 1

on page 1.

d. Secure the tower transmission cable to the mounting pipe or tower leg, using

tie-wraps or customer-supplied cable clamps.

e. Loop or drape any excess cable and tie-wrap it to the pipe, to prevent wind

damage to the cables and to ensure the weight of the cable is not carried by

the antenna input.

NOTE

The Model 6822 antenna does not require pressurization or purging. The

feed system up to the power divider may be pressurized.

Installation of your Model 6822 2- to 8-bay is now complete. Please proceed

Startup

on page 51.

Содержание 6822















































































Результаты поиска

Содержание 6822

Отзывы:

Shively Labs 6822, Инструкция по установке, эксплуатации и техническому обслуживанию, Страница: 45 / 78

Результаты поиска

Содержание 6822

Отзывы: