Shively Labs 6822 Скачать руководство пользователя страница 44

Страница: 44 / 78

Connecting the Antenna (8-bay)

Connect the antenna
bay cables.

CAUTION

Stressing a coax connection after assembly can detune the system.

Therefore, never make a connection and then bend or twist the cable, or

use the connector to force the coax into shape. Form the cable first,

then attach it to the connector.

CAUTION

The minimum single bending radius for HCA78-50J coax is 4" (100 mm).

The repeated bending radius is 10" (250 mm). Do not bend it too tightly;

you may damage it.

CAUTION

The minimum bending radius for 1/2" coax is 3" (8 cm). Do not bend it

too tightly; you may damage it.

CAUTION

Do not overtighten the connectors. Overtightening may damage them.

a. Connect the output end (90° connectors) of the antenna bay cable (47, 50,

56, or 59) to the DIN connector at the bottom of the endseal.

Figure 26. Antenna bay cable

connection

b. Run the cable along the antenna weldment and secure it, using tie-wraps

(44), so as to prevent it moving and chafing against the U-bolt or other

surfaces.

c. Connect the input end of the antenna bay cable to the power divider DIN

outputs.

d. Secure the cable to the mounting pipe or tower leg, using tie-wraps or

customer-supplied cable clamps.

e. Repeat for the other antenna bay(s).

Содержание 6822















































































Результаты поиска

Содержание 6822

Отзывы:

Shively Labs 6822, Инструкция по установке, эксплуатации и техническому обслуживанию, Страница: 44 / 78

Результаты поиска

Содержание 6822

Отзывы: