Assembly of Bunny
/ Playhut
Platform
Completed Platform
PLEASE LAY OUT PARTS AND CHECK OFF AGAINST CHECK LIST BELOW:
QTY DESCRIPTION
2: Rear Legs 70x70x970mm
2: Front Legs 70x70x1597mm
2: Side Framework 70x44x1736mm
2: Front/Back Framework 70x44x1190mm
3: Inner Framework 70x44x1102mm
2: Inner Framework 70x44x655mm
4: Leg Support Braces 70x44x822mm
1: Decking Board 119x28x950mm
4: Decking Board 119x28x1190mm
BUILT AROUND OUR REPUTATION
Adult Assembly Only - Do not attempt to modify this Pl
atform
Thank you and congratulations on the purchase of your Shire Garden Building. We believe that this product
will give you many years of excellent service. This is a natural product manufactured to a high standard
therefore if you have any queries or experience any difficulties then please contact our customer service
hotline on
01945
465 295
.
Normal office hours: 8.30 am to 5.00 pm
Monday to Friday.
We recommend that the base onto which your building will stand should be at least 75 mm larger in each
direction than the total floor size of the building.
Actual floor area of the building:
1
190
(1615 inc ladder)
x 1
824
mm
Total height clearance:
INC Bunny/Playhut 2406
mm
Platform height 998mm
The chosen position in your garden for the siting of the building should be excavated to a depth of 75 mm to
allow a base of sand, on to which paving slabs can be evenly laid -
THEY MUST BE LEVEL AND FIRM.
Treatment/Care of your Garden Building
Treat with a suitable decorative wood finish immediately. We recommend that all timber pieces be treated
again prior to assembly and again within 3 months of assembly. We further recommend that all pieces are
treated again at least annually or as frequently as the instructions on the product used recommends.
We would suggest that all wall panels be treated in an upside-down position to allow the finish/treatment to
ingress into the tongue and groove jointing.
Tools Required
IMPORTANT!
PLEASE READ PRIOR TO ASSEMBLY OF
THE BUILDING
EVERY PRECAUTION IS TAKEN TO
ENSURE THAT YOUR BUILDING HAS NO
ELEMENT INCORRECTLY PLACED OR
POSSIBLY HAZARDOUS, HOWEVER
PRIOR TO USE PLEASE CHECK ALL
SURFACES FOR THE FOLLOWING:
1 RAISED
GRAIN,
SPLINTERS:
sand
down timber to smooth finish
2 NAIL/SCREW/PIN HEADS PROUD: tap
home to be flush with surface of timber
3 DAMAGED SCREW HEADS
RESULTING IN SHARP SPLINTERS OF
METAL: replace
4 SHARP ENDS OF NAILS/ SCREWS/
PINS PROTRUDING THROUGH THE
PANEL: remove and reposition.
5 ENSURE ALL PARTS ARE SECURED
AGAINST REASONABLE FORCE:
remove and refit
6 ENSURE THERE ARE NO LOOSE
PARTS: remove and refit/discard
We recommend that protective gloves
be worn throughout
Wood is a natural product and is therefore
prone to changes in appearance, including
some warping, movement and splitting,
particularly during unusual climatic conditions
(long hot or wet spells of weather). As a natural
occurrence this is not covered by a guarantee.
PLEASE NOTE
PLEASE KEEP THIS LEAFLET FOR FUTURE REFERENCE
(
01
/0
3
/1
6
)
Posidrive screwdriver (electric is best)
Drill with 6 & 3 mm drill bits
Sandpaper (to smooth any rough edges)
Tape measure
Ruler
Pencil
Preparation of Base
Brigstock Road, Wisbech PE13 3JJ
We would also remind you that you would rarely (if ever) be able to re-treat the underside of the floor
following assembly. We strongly recommend that the underside of the floor is treated an absolute minimum of
twice (not including pre-treatment). Use only child safe wood preservative and allow to dry thoroughly before
further use. Do not use creosote.
Garden buildings are not waterproof, therefore on assembling building we recommend using a silicon
based sealant between wall panels and between wall panels and floor.
Parts List
PLATFORM FRAMEWORK
QTY DESCRIPTION
2: Rebated Profiles 44x34x962mm
2: Framework Pieces 34x22x506mm
11: Slats 70x12x535mm
PLATFORM RAILINGS
QTY DESCRIPTION
2: Notched Side Rails 44x44x1070mm
1: Top Step 44x44x470mm
3: Steps 57x25x470mm
PLATFORM STEPS
QTY DESCRIPTION
FIXINGS
Plese note rails and ladders may
be assembled
60: 80mm Screws
23
: 60mm Screws
38: 50mm Screws
44
:
25
mm Screws
FIXINGS
-
Assembled rails and
ladder
QTY DESCRIPTION
60: 80mm Screws
1
7
:
6
0
mm
Screws
38: 50mm Screws
