SM-BB80
FC-M815
FC-M810
83 mm
68, 73 mm
1.37 X 24 T.P.I.
Technical Service Instructions
SI-1L70A-001
SM-BB80
General Safety Information
WARNING
• If the inner cover is not installed correctly, the axle may rust and become
damaged, and the bicycle may fall over and serious injury may occur as a
result.
•
Obtain and read the service instructions carefully prior to installing the
parts.
Loose, worn or damaged parts may cause the bicycle to fall over
and serious injury may occur as a result. We strongly recommend only
using genuine Shimano replacement parts.
• Read these Technical Service Instructions carefully, and keep them in a
safe place for later reference.
Note
• If the bottom bracket shell is not parallel, gear shifting performance will
drop.
• Before riding the bicycle, check that there is no play or looseness in the
connection. Also, be sure to retighten the crank arms and pedals at
periodic intervals.
• If you feel any looseness in the bearings, the bottom bracket should be
replaced.
• In addition, if pedaling performance does not feel normal, check this once
more.
• Do not wash the bottom bracket with high-pressure jets of water.
• When installing the left and right adapters, be sure to install the inner
cover too, otherwise the waterproofing performance will drop.
• Apply grease to the left and right adapters before installing them.
• Be sure to read the service instructions for the front chainwheel in
conjunction with these service instructions.
• Parts are not guaranteed against natural wear or deterioration resulting
from normal use.
• For maximum performance we highly recommend Shimano lubricants and
maintenance products.
• For any questions regarding methods of installation, adjustment,
maintenance or operation, please contact a professional bicycle dealer.
■
Spacer installation method
(1) Check whether the width of the bottom bracket shell is 68 mm,
73 mm or 83 mm.
(2) Next, install the adapter while referring to the illustrations
below.
Installation of the adapter
Use the TL-FC32/36 special tool to install the right adapter (counterclockwise
thread), the inner cover and the left adapter (clockwise thread).
68 / 73 / 83 mm
For bracket type
Install as shown in the illustration.
Bolt
Adapter
Adapter
Front Derailleur
Left hand adapter
Front Chainwheel
Tightening torque :
35 - 50 N·m {305 - 435 in. lbs.}
Tightening torque :
35 - 50 N·m {305 - 435 in. lbs.}
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222
3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
Please note: specifications are subject to change for improvement without notice. (English)
© Sep. 2008 by Shimano Inc. XBC SZK Printed in Japan.
Right hand adapter
Inner cover
Bottom bracket shell width
Thread dimensions
Bottom Bracket
Specifications
Applicable front chainwheel
Model number
■
Chain Device
When installing a BB mount-type chain device to a
bicycle, refer to the table below to determine the number
of spacers for the right side. If the thickness of the
spacers used is not as given in the table, the front
chainwheel may become loose and fall off, or problems
with gear shifting may occur. When installing a BB mount-
type chain device or a ISCG-type chain device to a
bicycle, you need to be careful to avoid interference.
68 mm
73 mm
83 mm
Bottom bracket shell width
Model number
When using in combination with the FD-M665-E
(2.5 mm chain device)
<Installation method>
Install the chain device and the front
derailleur as shown in the illustration.
• If using in combination with an BB mount-
type front derailleur, make sure that the
chain device does not obstruct the BB
mount-type bracket.
Not needed
No available
Not needed
FC-M665 FC-M810-2
FC-M815-2
BB mount-type
bracket
Chain Device
F
A
F
A
F
A
: 2.5 mm spacer
68 mm
83 mm
68 mm
73 mm
83 mm
Bottom bracket shell width
Model number
For chain device
thickness of 2.5 mm
2.5 mm x 1
Not needed
2.5 mm x 1
FC-M810-1 FC-M665
FC-M810-2
FC-M665
FC-M815-1 FC-M815-2
68 mm
73 mm
83 mm
Bottom bracket shell width
Model number
For chain device
thickness of 5.0 mm
Not needed
No available
Not needed
FC-M810-1 FC-M665
FC-M810-2
FC-M665
FC-M815-1 FC-M815-2
The example in the
illustration shows a BB
mount-type chain device.
<Chain Device Thickness (BB mount)>
SI-1L70A-001-00
00
Band Type
Bottom bracket shell width
Bracket Type
BB mount-
type bracket
(2.5mm)
(2.5mm)
(2.5mm)
(2.5mm)
(2.5mm)
(2.5mm)
BB mount-
type bracket
(2.5mm)
(2.5mm)
(2.5mm)
(2.5mm)
(2.5mm)
68 mm
73 mm
83 mm
