background image

4

IMPORTANT NOTICE

IMPORTANT NOTICE

 

• This dealer's manual is intended primarily for use by professional bicycle mechanics.

Users who are not professionally trained for bicycle assembly should not attempt to 
install the components themselves using the dealer's manuals.
If any part of the information on the manual is unclear to you, do not proceed with the 
installation. Instead, contact your place of purchase or a distributor for assistance.

 

Make sure to read all manuals included with the product.

 

Do not disassemble or modify the product other than as stated in the information 
contained in this dealer's manual.

 

All manuals and technical documents are accessible online at https://si.shimano.com.

 

For consumers who do not have easy access to the internet, please contact a SHIMANO 
distributor or any of the SHIMANO offices to obtain a hardcopy of the User's Manual.

 

Please observe the appropriate rules and regulations of the country, state or region in 
which you conduct your business as a dealer.

 

The Bluetooth

®

 word mark and logos are registered trademarks owned by the Bluetooth 

SIG, Inc. and any use of such marks by SHIMANO INC. is under license. Other trademarks 
and trade names are those of their respective owners.

For safety, be sure to read this dealer's manual thoroughly before use, and 
follow it for correct use.

The following instructions must be observed at all times in order to prevent personal injury 
and physical damage to equipment and surroundings.
The instructions are classified according to the degree of danger or damage which may occur 
if the product is used incorrectly.

DANGER

Failure to follow the instructions will result in death or serious 
injury.

WARNING

Failure to follow the instructions could result in death or 
serious injury.

CAUTION

Failure to follow the instructions could cause personal injury or 
physical damage to equipment and surroundings.

Содержание EW-EN100





























































Отзывы: