manualshive.com logo in svg

Shimadzu AUW120, Инструкция по эксплуатации

Поделиться
Скачать
Shimadzu AUW120 Скачать руководство пользователя страница 37

24

6.  WindowsDirect Function

6.2.4

Start and Checking Operation

1

Confirm Windows

®

 is free from any application.

2

After Windows

®

 has completely started, con-

nect power cable from the AC adapter to the bal-
ance, when “oFF” is displayed, press the

[POWER]

 key. The mass display appears.

3

Open the “Note pad” accessory in Windows

®

*

(or start the application you wish to use).

4

Press the 

[PRINT]

 key of the balance.

Verify that the numeric value displayed on the bal-
ance appears at the cursor position on the screen
of computer. The effect is the same as typing the
value from the computer keyboard and pressing
the ENTER key. Characters indicating the unit of
measure are not sent to the computer.

5

Test combination with Auto Print function, if you

wish to use it. 

6

End the operation using the standard close or

exit procedure.

Windows

®

* = Windows

®

 95, Windows

®

 98, Windows

®

 Me, Windows

®

 2000, Windows

®

 XP, and higher.

   Note

Turning on the balance before Windows

®

* is completely activated may

cause incorrect operation.

Содержание AUW120
























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды