Shield M10U Скачать руководство пользователя страница 65

Страница: 65 / 72

Chapter 9 Product Specification

Shield M10U user manual

Chapter 9 Product Specification

This chapter provides UPS product specification.

9.1 Applicable Standards

The UPS has been designed to conform to the following European and international standards:

Table.9- 1: Compliance with European and International Standards

Item

Normative reference

General safety requirements for UPS used
in operator access areas

EN50091-1-1/IEC62040-1-1/AS 62040-1-1

Electromagnetic

compatibility

(EMC)

requirements for UPS

EN50091-2/IEC62040-2/AS 62040-2(C3)

Method of specifying the performance and
test requirements of UPS

EN50091-3/IEC62040-3/AS 62040-3(VFI SS 111)

Note:

The above mentioned product standards incorporate relevant compliance clauses with generic IEC and EN

standards for safety (IEC/EN/AS60950), electromagnetic emission and immunity (IEC/EN/ AS61000 series) and
construction (IEC/EN/AS60146 series and 60950).

9.2 Environmental Characteristics

Table.9- 2: Environmental Properties

Items

Unit

Requirements

Acoustic noise level at 1 meter

56.0(power module)

Altitude of Operation

≤1000m above sea level, derate power by 1% per 100m between
1000m and 2000m

Relative Humidity

%RH

0 to 95%, non condensing

Operating Temperature

°C

0 to 40 deg , Battery life is halved for every 10°C increase above
20°C

UPS

Storage-Transport

Temperature

°C

-20~70

Recommended Battery Storage
Temperature

°C

0~25 (20°C for optimum battery storage)

9.3 Mechanical Characteristics

Table.9- 3: Mechanical Properties

Cabinet Specification

Unit

20/10

40/10

60/10

Mechanical
Dimension, W×D×H

446×697×398(7U)

446×697×575(11U)

485*751*1033

Weight

Color

N/A

Black

Protection

Level,

IEC(60529)

N/A

IP20

Module type

Unit

Mechanical

Dimension,

W×D×H

436×590×85

Weight

15.3

Color

N/A

Black(front)

Содержание M10U









































































Результаты поиска

Содержание M10U

Отзывы:

Shield M10U, Руководство пользователя, Страница: 65 / 72

Результаты поиска

Содержание M10U

Отзывы: