ShenZhen Yuejiang Technology Dobot Magician Скачать руководство пользователя страница 10

Страница: 10 / 153

Dobot Magician User Guide

Dobot Magician Homing Operation

Issue V1.9.0 (2020-07-23)

User Guide

Figure 2.2 Connect the Dobot Magician to your computer

Installing the DobotStudio

You can control Dobot Magician by DobotStudio to implement functions such as Teaching &

Playback, fully programmable applications, and 3D printing. This topic introduces Teaching &

Playback.

System Requirements

The DobotStudio supports the following Windows and macOS versions.



Windows 7, Windows 8, and Windows 10 (This manual is explained based on this version)



macOS 10.10, macOS 10.11, and macOS 10.12

Obtaining the DobotStudio Package

Before using Dobot Magician, download the Windows DobotStudio package from

https://www.dobot.cc/downloadcenter.html

. The macOS version is also downloadable in this URL.

Installing the DobotStudio

Prerequisites

The DobotStudio package has been obtained.

Procedure

Unpack the DobotStudio package to a destination directory.

Содержание Dobot Magician


























































































































































Результаты поиска

Содержание Dobot Magician

Отзывы:

Похожие инструкции для Dobot Magician

Бренды по названию

Популярные бренды

ShenZhen Yuejiang Technology Dobot Magician, Руководство пользователя

Результаты поиска

Содержание Dobot Magician

Отзывы:

Похожие инструкции для Dobot Magician

Бренды по названию

Популярные бренды