manualshive.com logo in svg

Shel lab SMI11, Инструкция по установке и эксплуатации, Страница: 6 / 36

Поделиться
Скачать
Shel lab SMI11 Скачать руководство пользователя страница 6

6 | 

P a g e

 

INTRODUCTION 

 

C

ONTACTING 

A

SSISTANCE

 

Phone hours for Sheldon Technical Support are 6 am – 4:30 pm Pacific Coast Time (west coast of 

the United States, UTC -8). Please have the following information ready when calling or emailing 

Technical Support: the 

model number

 and the 

serial number 

(see page 8). 

EMAIL: [email protected] 

PHONE: 1-800-322-4897 extension 4, or (503) 640-3000  

FAX: (503) 640-1366 

Sheldon Manufacturing, INC. 
P.O. Box 627 
Cornelius, OR 97113 

 

 

T

EMPERATURE 

R

EFERENCE 

S

ENSOR 

D

EVICE

 

This unit does not come with a temperature reference device

. A reference 

device must be purchased separately

 for performing in-house accuracy 

validations or calibration adjustments of the incubator temperature display. 

The device must be accurate to at least 0.1°C and should be regularly 

calibrated by a third party. For best results, use a digital device with one or 

more thermocouple probes. Remote readings eliminate chamber door openings and avoid 

subsequent waits for the chamber temperature to re-stabilize. Select probes suitable for the 

application temperature you will validate or correct the display accuracy at.

 

Alcohol thermometers are insufficient for conducting accurate validations and calibrations. Do not 

use a mercury thermometer. 

Never place a mercury thermometer in the incubation chamber. 

Always use thermocouple probes. 

 

 

E

NGINEERING 

I

MPROVEMENTS

 

Sheldon Manufacturing continually improves all of its products. As a result, engineering changes and 

improvements are made from time to time. Therefore, some changes, modifications, and 

improvements may not be covered in this manual. If your unit’s operating characteristics or 

appearance differs from those described in this manual, please contact your SHEL LAB dealer or 

customer service representative for assistance. 

Содержание SMI11





































Отзывы:

Нет отзывов