manualshive.com logo in svg

Shel lab SMI11, Инструкция по установке и эксплуатации, Страница: 5 / 36

Поделиться
Скачать
Shel lab SMI11 Скачать руководство пользователя страница 5

5

 | 

P a g e

 

INTRODUCTION 

 

Thank you for purchasing a SHEL LAB Incubator. We know you have many choices in today’s competitive 

marketplace when it comes to constant temperature equipment. We appreciate you choosing ours. We 

stand behind our products and will be here for you if you need us. 

R

EAD THIS 

M

ANUAL

 

Failure to follow the guidelines and instructions in this user manual may create a protection 

impairment by disabling or interfering with the unit safety features. This can result in injury or death. 

Before using the unit, read the manual in its entirety to understand how to install, operate, and 

maintain the unit in a safe manner. Keep this manual available for use by all operators. Ensure all 

operators are given appropriate training before the unit begins service. 

 

S

AFETY 

C

ONSIDERATIONS AND 

R

EQUIREMENTS

 

Follow basic safety precautions, including all national laws, regulations, and local ordinances in your 

area regarding the use of this unit. If you have any questions about local requirements, please 

contact the appropriate agencies. 

SOPs

 

Because of the range of potential applications, this unit can be used for, the operator or their 

supervisors must draw up a site-specific standard operating procedure (SOP) covering each 

application and associated safety guidelines. This SOP must be written and available to all operators 

in a language they understand. 

Intended Applications and Locations 

The incubators are intended for constant temperature, non-humidified general incubation 

applications in professional, industrial, and educational environments. The units are not intended for 

use at hazardous or household locations.  

Power 

Your unit and its recommended accessories are designed and tested to meet strict safety 

requirements.  

•

 

The unit is designed to connect to a power source using the specific power cord type 

shipped with the unit. 

•

 

Always plug the unit power cord into a protective earth grounded electrical outlet 

conforming to national and local electrical codes. If the unit is not grounded properly, parts 

such as knobs and controls can conduct electricity and cause serious injury. 

•

 

Do not bend the power cord excessively, step on it, or place heavy objects on it. 

•

 

A damaged cord can be a shock or fire hazard. Never use a power cord if it is damaged or 

altered in any way. 

•

 

Use only approved accessories. Do not modify system components. Any alterations or 

modifications to your unit can be dangerous and void your warranty. 

Содержание SMI11





































Отзывы:

Нет отзывов