Shel lab SMI11 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 36

Shel lab SMI11 Скачать руководство пользователя страница 12

12 |

P a g e

INSTALLATION

L

IFTING AND

H

ANDLING

The unit is heavy. Use appropriate lifting devices that are sufficiently rated for these loads. Follow these

guidelines when lifting the unit.

•

Lift the unit only from its bottom surface.

•

Doors, handles, and knobs are not adequate for lifting or stabilization.

•

Restrain the unit completely while lifting or transporting so it cannot tip.

•

Remove all moving parts, such as shelves and trays, and lock doors in the closed position

during transfers to prevent shifting and damage.

L

EVELING

Install the 4 leveling feet with the 4 corner holes on the bottom of the unit. The unit must be level and

stable for safe operation.

Note:

To prevent damage when moving the unit, turn all four leveling feet so that the leg of each

foot sits inside the unit.

I

NSTALL

I

NCUBATOR IN

L

OCATION

Install the unit in a workspace location that meets the criteria discussed in the previous entries of the

Installation section.

I

NSTALLATION

C

LEANING

Cleaning and disinfecting the incubation chamber during installation reduces the chance of microbiological

contamination. The unit was cleaned and disinfected at the factory. However, the unit may have been

exposed to contaminants during shipping. Additionally, the factory procedure may not meet the standards

of your institutional protocols. Please see the

Cleaning and Disinfecting

entry on page 25 in the User

Maintenance section for information on how to clean and disinfect without damaging the chamber.

•

Remove all wrappings and coverings from shelving prior to cleaning and installation.

«
...
10
11
12
13
14
...
»

Содержание SMI11





































Отзывы:

Нет отзывов