Shel lab SCO5W Скачать руководство пользователя страница 38

Страница: 38 / 62

P a g e

OPERATION

UTING THE

UDIBLE

LARM

A visual devation indicator alarm illuminates if the chamber CO

level deviates 1% above or below the

set point. An audible alarm sounds immediately for a high deviation. The low deviation audible

alarm sounds only after the visual low indicator light has been continually illuminated for 15 minutes.
This delay prevents the alarm from sounding each time the chamber doors are opened.

To mute a CO

deviation alarm:

Press and hold the Set CO

Down

arrow button until the Mute light

illuminates.

•

The alarm will stay muted for the duration of the current
temperature deviation.

•

A new deviation of 1% or more will reactivate the audible alarm.

Low and No Gas Alarms Timeline

UPPLY

LARM

A second alarm activates if the Low Gas deviation indicator light is illuminated for longer
than 20 minutes.

•

The letters “ngS” will appear in the CO

display indicating

No Gas Supply

•

The alarm will remain active, even if the incubator is turned off and back on.

•

The NGS alarm remains on until CO

is restored to the chamber. It may take 2 or more

minutes of CO

injections to establish a concentration high enough to deactivate the

alarm.

Low Gas Alarm Muted

No Gas Supply

Содержание SCO5W































































Результаты поиска

Содержание SCO5W

Отзывы:

Shel lab SCO5W, Руководство по установке и эксплуатации, Страница: 38 / 62

Результаты поиска

Содержание SCO5W

Отзывы: