Shel lab SCO5W Скачать руководство пользователя страница 37

Страница: 37 / 62

37 |

P a g e

OPERATION

ET THE

OINT

The incubator comes from the factory with the CO

set point set to Off. Set the set point percentage

to the gas concentration required by your study or production protocol.

LO - Low CO

When starting with no CO

in the chamber, the display will show “LO” until the incubator registers a

concentration greater than 0%. A few minutes of CO

injections may be required to build up a

sufficient gas concentration.

End of Procedure

Navigate to the CO

Set Point Adjustment mode

Press and hold

either

Set CO

Set Point Adjustment Mode

Note: The display will automatically exit the adjustment mode after 5 seconds of

inactivity on the arrow keys, saving the last shown set point value.

Set the CO

Set Point

Set CO

New Set Point

Adjust

Note: To turn the CO

system off, set the set point

to its lowest setting (OFF).

Wait for 5 seconds after entering the Set Point

Set CO

The display will stop flashing. The set point is now saved in the controller.

The display will revert to showing the current chamber CO

concentration.

Injecting

Set CO

Initial Set Point

Содержание SCO5W































































Результаты поиска

Содержание SCO5W

Отзывы:

Shel lab SCO5W, Руководство по установке и эксплуатации, Страница: 37 / 62

Результаты поиска

Содержание SCO5W

Отзывы: