Sharp UX-B800A, Руководство по обслуживанию, Страница: 53 / 140

UX-B800A
2 – 39
SW110 No. 4 ~ No. 8 Reserved
SW111 No. 1 ~ No. 4 Detect time of LAN link ON
Used to change the setting for the link ON detection time when con-
necting a LAN cable.
SW111 No. 5 ~ No. 8 Detect time of LAN link OFF
Used to change the setting for the link OFF detection time when con-
necting a LAN cable.
SW112 No. 1 Default file format for network scan
SW setting the default of the compression format and the file type
required for generating the image data from network scanned data.
SW112 No. 2, No. 3 Default resolution for network scan
SW setting the default resolution on network scanning.
SW112 No. 4 ~ No. 7 Reserved
SW112 No. 8 SMTP authentication type
Used to switching the SMTP authentication type.
"0": The authentication type which is not supported by the server is
disabled.
"1": Authenticated from "LOGIN" regardless of the authentication type
of the server.
SW113 No. 1 ~ No. 8 Reserved
SW114 No. 1 ~ No. 5 DTMF output level (High)
To set the level to output high group DTMF signals. -15 to 0 dBm
(0.5dBm unit)
SW114 No. 6 ~ No. 8 Reserved
SW115 No. 1 ~ No. 5 DTMF output level (Low)
To set the level to output low group DTMF signals. -15 to 0 dBm
(0.5dBm unit)
SW115 No. 6 ~ No. 8 Reserved
SW116 No. 1 ~ No. 3 Dial tone detection frequency
To select frequency range of signals to be detected as Dial Tone.
SW116 No. 4, No. 5 Busy tone detection frequency
To select frequency range of signals to be detected as Busy Tone.
SW116 No. 6 ~ No. 8 Reserved
SW117 No.1 ~ No. 4 Number of rings for auto-receive (0: No ring
receive)
When the machine is set in the auto receive mode, the number of rings
before answering can be selected. It may be set from zero to nine
rings using a binary number. If the soft switch was set to 1, a direct
connection is made to the facsimile. If it was above 9, receive rings are
set to 9.
SW117 No.5 ~ No. 8 Distinctive ringring
When set to "0001", machine recognize the CI signal FAX ringing or
TEL ringing automatically.
SW118 No. 1 ~ No. 8 Reserved
SW119 No. 1 ~ No. 3 Reserved
SW119 No. 4 ~ No. 6 CI signal min. off time
Used to set the maximum length of CI signal off time, which is used to
determine a sequence of CI signals.
SW119 No. 7, No. 8 Reserved
SW120 No. 1 ~ No. 4 Reserved
SW120 No. 5 ~ No. 8 CI Signal Frequency
Used to set a frequency that is considered as the CI signal.
SW121 ~ SW140 No. 1 ~ No. 8 Reserved
SW141 No. 1, No. 2 Delay timer before line connect in auto dial
Set a time period between start of dial operation and line connection in
the auto dial mode.
SW141 No. 3, No. 4 Delay timer after line connect in auto dial
Set a time period between dial-up line connection and dial data trans-
mission in the auto dial mode.
SW141 No. 5, No. 6 Calling time
Set the call time for dialing in the auto dial mode.
SW141 No. 7, No. 8 CNG timing
Set a time period between dialing in the auto dial mode and CNG sig-
nal transmission.
SW142 No. 1 Dial tone detection (before auto dial)
When set to "1", a number is dialed after detecting the dial tone.
SW142 No. 2 Busy tone detection (after auto dial)
When set to "1", the busy tone is detected after dialing a number.
SW142 No. 3 Recall Control (for FCC part68)
Recalling fixed only one time when dialing was unsuccessful without
detecting busy tone signal.
SW142 No. 4 ~ No. 8 Reserved
SW143 ~ SW195 No. 1 ~ No. 8 Reserved
SW196 No. 1 ~ No. 3 Reserved
SW196 No. 4, No. 5 Busy tone detect pulse in TEL/FAX mode
This setting is used for the detection pulse number until busy tone is
detected in the TEL/FAX mode.
SW196 No. 6 Dial tone detect time in TEL/FAX mode
This setting is used for the continuous detection time until dial tone is
detected in the TEL/FAX mode.
SW196 No. 7, No. 8 Reserved
SW197 ~ SW300 No. 1 ~ No. 8 Reserved