background image

1

KB-0333KS
KB-0333KK
KB-0333KW

S65H253KB033K

KB-0333KS
KB-0333KK
KB-0333KW

INSIGHT RANGE HOOD

MODELS

SERVICE MANUAL

SHARP CORPORATION

This document has been published to be used for after
sales service only.
The contents are subject to change without notice.

TABLE OF CONTENTS

Page

PRECAUTIONS TO BE OBSERVED BEFORE BEFORE SERVICING ......................... INSIDE FRONT COVER
WARNING TO SERVICE PERSONNEL .............................................................................................................. 1
FOREWORD AND WARNING ............................................................................................................................. 1
PRODUCT SPECIFICATIONS ............................................................................................................................ 2
WIRE HARNESS DRAWING ............................................................................................................................... 3
COMPONENT REPLACEMENT .......................................................................................................................... 4
PARTS LIST ........................................................................................................................................................ 6

Содержание KB-0333KK













Отзывы: