background image

OPERATION MANUAL

FOR YOUR RECORDS    

For your assistance in reporting this unit in case of loss
or theft, please record below the model number and serial
number which are located on the rear of the unit. 

Please  retain  this  information.       

Model number  _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Serial number  _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Date of purchase _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Place of purchase  _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

MODEL

CD-BA150

HK

<P=001>

MINI COMPONENT SYSTEM

Thank you for purchasing this SHARP product. 
To obtain the best performance from this product,
please read this manual carefully.  
It will guide you in operating your SHARP product.

CD-BA150 Mini Component System consisting of 
CD-BA150 (main unit) and CP-BA150 (speaker system).

Note:

This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harm-
ful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a par-
ticular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

WARNING

FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could void
the user’s authority to operate this equipment.

C A U T I O N

R I S K O F E L E C T R I C S H O C K

D O N O T O P E N

The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated "dangerous
voltage" within the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.       

CAUT I ON:   TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NO T  REM OVE  COVER  ( OR
BACK).
NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSON-
NEL.    

The exclamation point within an equi-
lateral triangle is intended to alert the
user to the presence of important
operating and maintenance (servic-
ing) instructions in the literature ac-
companying the appliance.   

Caution - use of controls or adjustments or per-
formance of procedures other than those specified
herein may result in hazardous radiation exposure.

WARNING: TO REDUCE THE RISK OF
FIRE OR ELECTRIC SHOCK, DO NOT EX-
POSE THIS APPLIANCE TO RAIN OR
MOISTURE.

       

Note:

It is the intent of Sharp that this product be used in
full compliance with the copyright laws of the United
States and that prior permission be obtained from
copyright owners whenever necessary.    

CD-BA150(SEC) TINSE0279AWZZ

Содержание CD-BA150



















Отзывы: