manualshive.com logo in svg

Sharp AR-C260P, Руководство по эксплуатации

Поделиться
Скачать
Sharp AR-C260P Скачать руководство пользователя страница 42

MISFEED REMOVAL

2-24

Misfeed in the paper feed area

Misfeed in the 500 sheet paper drawer

1

Open the upper side cover.

Push the blue lever
upward and gently open
the cover.

2

Remove the misfed paper.

Be careful not to tear the
misfed paper during
removal.

3

If misfed paper is not found in step 2, pull out
paper tray 1 and remove the misfed paper.

Be careful not to tear the
misfed paper during
removal.

4

Gently close the paper tray.

Push the tray firmly all
the way into the
machine.

5

Gently close the upper side cover.

After closing, confirm
that the misfeed
message has been
cleared and the normal
display appears.

Misfeed in the bypass tray

1

Remove the misfed paper from the bypass
tray.

Be careful not to tear the
misfed paper during
removal.

2

After removing the misfed paper, open
and close the duplex bypass/inverter unit
to reset.

Grasp the finger hold
and gently open the unit. 

After closing, confirm that
the misfeed message
has been cleared and the
normal display appears.
If the duplex
bypass/inverter unit is not
installed, close the side
cover in the same way.

NOTE

Paper misfed from a paper tray may be extending out of the tray into the right side cover area. If the tray is drawn
out of the machine in this case, the paper may tear and become difficult to remove. To prevent this from happening,
always open the right side cover first and remove the misfed paper if it is extending into that area.

NOTE

If paper is loaded in the bypass tray, remove the
paper and close the bypass tray before opening the
side cover.

NOTE

The misfeed may have occurred inside the machine.
Check carefully and remove it.

Содержание AR-C260P















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды