Sharp AR-BC260 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 184

Sharp AR-BC260 Скачать руководство пользователя страница 74

4-6

SETTING ORIGINALS

■

■

■

■

When using the reversing single
pass feeder

1

Adjust the original guides to the size of the
originals.

2

Place the originals face up in the
document feeder tray.

Set the originals all the
way into the feed slot.
Do not exceed the
maximum height line
marked on the original
guide.

■

■

■

■

When using the document glass

Open the document cover, place the
original face down on the document glass,
and then gently close the document cover.

[ How to place the original ]

Place the original in the appropriate position shown
below according to its size. (

Center the original on

the centering scale.)

* When the reversing single pass feeder is used, these sizes are only supported for one-sided originals.

NOTES

●

Do not place any objects under the original size
detector, because they may damage it or the
original size may not be detected properly.

●

If an original has been placed in the document
feeder tray of the reversing single pass feeder,
remove it. Otherwise the original in the document
feeder tray will be scanned instead of the original
on the document glass.

Original size detector

R

R

8½x14
or B4

11x17 or A3

8½x11 or A4

8½x11
or A4

5½x8½
or A5

Original scale

Centering scale

Original scale

Centering scale

NOTE

Original size detection function

One of the four groups of standard original sizes shown below can be selected for detection by the original size
detection function. The factory default setting is "INCH-1 (AB-1)". The setting can be changed using "ORIGINAL
SIZE DETECTOR SETTING" in the key operator programs. (Page 11 of the key operator's guide.)

Group

Detectable original sizes

Document feeder tray (for reversing single pass feeding) or document glass

1

INCH - 1

11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 5-1/2" x 8-1/2"*

2

INCH - 2

11" x 17", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 5-1/2" x 8-1/2"*

3

AB - 1

A3, A4, A4R, A5, B4, B5, B5R

4

AB - 2

A3, A4, A4R, A5, B5, B5R, 8-1/2" x 13"

ApollonII_general-copy_SEC.book 6

ページ

２００４年９月６日　月曜日　午後４時５７分

«
...
72
73
74
75
76
...
»

Содержание AR-BC260

























































































































































































Отзывы:

Нет отзывов