Sharp AR-BC260 Скачать руководство пользователя страница 57

Страница: 57 / 184

SADDLE STITCH FINISHER

3-9

Raise the lever at the end of the staple box.

Remove the top staple if
it is bent. If bent staples
remain, a staple jam will
occur again.

Return the lever to its original position.

Reinstall the staple box.

Push the staple box in
until it clicks into place.

Push the stapler section back into the
finisher.

Close the front cover.

Push the saddle stitch finisher back
against the main unit.

■

Disposal of hole punch scrap (when the punch unit is installed)

Unlatch the saddle stitch finisher and slide
it away from the main unit.

Pull out the punch scrap collecting
container and empty it.

Discard the punch
scraps in a plastic bag or
other container, taking
care not to let the scraps
scatter.

Return the punch scrap collecting
container to its original position.

Push the saddle stitch finisher back
against the main unit.

NOTE

Make a test print or copy in the staple sort mode to
ensure that stapling is performed properly.

sec_apollon_03-1.fm 9

ページ

２００４年１１月１５日　月曜日　午前１１時４５分

Содержание AR-BC260

























































































































































































Результаты поиска

Содержание AR-BC260

Отзывы:

Sharp AR-BC260, Руководство по эксплуатации, Страница: 57 / 184

Результаты поиска

Содержание AR-BC260

Отзывы: