Sharp AR-BC260 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 184

Sharp AR-BC260 Скачать руководство пользователя страница 52

SADDLE STITCH FINISHER

3-4

Saddle stitch finisher functions

■

■

■

■

Sort mode

Sorted sets will be delivered.

■

■

■

■

Group mode

Groups of copies of the same page will be
delivered.

■

■

■

■

Offset mode

Sets will move from side to side so that each set or
group will be offset from the previous set or group
for easy separation.
(The offset function only operates in the offset
tray.)
Stapled sets will not be offset.

■

■

■

■

Staple sort mode

Collated sets of prints or copies will be stapled and delivered to the offset tray. When saddle stitching is selected,
the prints or copies will be stapled at the center and delivered to the saddle stitch tray. The stapling positions,
orientation, paper size for stapling, and stapling capacity are shown below.

Printouts

Original

Printouts

Original

Offset mode

Non-offset mode

Stapling positions

Top left corner of
printouts

Lower left corner
of printouts

Portrait orientation

Landscape orientation

Available paper sizes:
8-1/2" x 11", A4 and B5
Stapling capacity:
For each size, up to 30 sheets
can be stapled

Same as above

Available paper sizes: 11" x 17",
8-1/2" x 14", 8-1/2" x 13", 8-1/2"
x 11"R, A3, B4 and A4R
Stapling capacity: Up to 30
sheets of 8-1/2" x 11"R or A4R
paper can be stapled, up to 25
sheets of other paper sizes

Saddle stitch on
centerfold line.

Paper in the portrait
direction cannot be saddle
stitched.

Available paper sizes: 11" x17",
8-1/2" x 11"R, A3, B4 and A4R
Stapling capacity: For each
size, up to 10 sheets can be
stapled

Center left two
positions of
printouts

Same as above

Same as above

Same as above

ApollonII_general-copy_SEC.book 4

ページ

２００４年９月６日　月曜日　午後４時５７分

«
...
50
51
52
53
54
...
»

Содержание AR-BC260

























































































































































































Отзывы:

Нет отзывов