LC-60/70EQ10U,SQ10U/15U/17U,TQ15U,UQ17U
5 – 18
10. Key writing
10.1. EDID writing (Main PWB: QPWBXG381WJ**/QPWBXG382WJ**)
1. Write the EDID key data on IC3103 mounted on the main PWB.
2. Carry out thorough data management to avoid redundant writing of data.
If the IC where data is written is damaged, replace the PWB since only the IC cannot be changed.
10.2. MAC key writing (MAIN PWB: QPWBXG381WJ**/QPWBXG382WJ**)
1. Write the NETFLIX/WMDRM key data on IC3103 mounted on the main PWB.
2. Carry out thorough data management to avoid redundant writing of data.
If the IC where data is written is damaged, replace the PWB since only the IC cannot be changed.
10.3. NETFLIX/WV(RoxioNow)&WMDRM key writing HDCP 2.2(Miracast) (MAIN PWB: QPWBXG381WJ**/QPWBXG382WJ**)
1. Write the wide vine key data on IC3103 mounted on the main PWB.
2. Carry out thorough data management to avoid redundant writing of data.
If the IC where data is written is damaged, replace the PWB since only the IC cannot be changed.
NOTE: For EDID of the analog RGB (DSUB 15pin), write the data on the process menu just like HDMI.
10.4. Update Logic Serial No. writing (MAIN PWB: QPWBXG381WJ**/QPWBXG382WJ**)
11. Factory setting
After completing the factory setting, pull out the AC cord to complete the setting.
CAUTION: Do not turn on the power after completing the factory setting. If the power is turned on, configure the factory setting again.
Adjustmeent Point
Adjustment conditions
Adjustment procedure
1
HDMI EDID writing
Analog RGB EDID
writing
(Main PWB)
Process mode
Model discrimination check
1. Enter the process mode.
2.QPWBXG381WJ**/QPWBXG382WJ**
Point the cursor to [HDMI EDID WRITE] and press the [ENT] key.
The writing is complete when [OK] is displayed.
3.QPWBXG382WJ**
Point the cursor to [HDMI EXTERNAL EDID WRITE] and press the [ENT] key.
The writing is complete when [OK] is displayed.
[Caution]
Perform the data wriring after setting the model discrimination.
The data based on the model discrimination information is recorded in EEPROM.
When applying 3., please be performed in a state of disconnect the cable from the HDMI
terminal always.
Adjustment point
Adjustment conditions
Adjustment procedure
1
Factory setting
Complete the setting by
pulling out the AC cord.
•
Point the cursor to [INDUSTRY INIT (+Cause)], set to “ON” using [+]/[-] of the [VOL]
key, and press the [ENT] key.
The version confirmation screen appears on the green screen. It is completed when
[SUCCESS] is displayed at the top.
(If error occurs, [ERROR] is displayed on the red screen.)
•
Turn off the AC power.
The following items are initialized when configuring the factory setting.
1) User set value
2) Channel data (broadcasting frequency, etc.)
3) Password setting value
4) Operating time
5) Standby Cause
6) Auto installation flag
7) V-CHIP block setting value
Содержание Aquos LC-60SQ10U
