16
Setting the CLOCK
AUTO CLOCK Setting
There are two methods of setting the clock: AUTO CLOCK
and MANUAL CLOCK. AUTO CLOCK uses EDS signals,
which are provided by some TV stations, to automatically
adjust the clock. MANUAL CLOCK sets the clock manually
in areas where no channel carries EDS signals.
Press
MENU
to display the Menu screen.
Press
\
/
|
to select “SETUP”.
Press
'
/
"
to select “CLOCK”, and press
ENTER
.
SETUP�
��OPTION
C H � S E T U P
M T S
C L O C K
I N P U T 3 � S E L E C T
V ﾐ C H I P � B L O C K
C L O S E D � C A P T I O N
C O L O R � S Y S T E M
H D M I � S E T U P
P C � S E T U P
L A N G U A G E
Press
'
/
"
to select “SET”, and press
ENTER
.
S E T
T I M E D I S P L A Y A U T O
M A N U A L
Press
'
/
"
to select “AUTO”, and press
ENTER
.
●
If you do not know the channel that carries EDS signals in your
area, set “EDS CH” to “AUTO” and press
ENTER
. If you know the
channel of the EDS signal carrier in your area, press
\
/
|
to select
the channel and press
ENTER
.
S E T
T I M E D I S P L A Y E D S C H A U T O
●
When set to “AUTO CLOCK”, the current time is acquired
automatically when the main power is turned OFF. (This function
will not work when EDS CH is not set.)
■
Backup
The clock function is maintained for about 5 minutes even
when the AC cord has been shut off due to a power outage
or when moving the LCD TV set. (Since about 30 minutes
are required to charge the backup power supply, it may not
be possible to maintain the clock function if the charging
time is excessively short.)
If the clock setting has been reset, repeat the procedures on
this page.
1
3
4
MANUAL CLOCK Setting
If there are no channels with EDS signals, set the clock
manually using MANUAL CLOCK.
Repeat steps
1
to
4
of
AUTO CLOCK Setting
.
Press
'
/
"
to select “MANUAL”, and press
ENTER
.
S E T
T I M E D I S P L A Y A U T O
M A N U A L
Press
'
/
"
to select “DST”, and press
\
/
|
to select
“ON” or “OFF”.
Press
'
/
"
to select “TIME”, and press
\
/
|
to set the
time, and press
ENTER
.
12:00AM
11:59AM
11:59PM
12:00PM
• Holding down
\
/
|
changes the setting at a high speed.
S E T
T I M E
�
D I S P L A Y
� �
D S T
� � �
O F F
�
� � � � � � � � � � � � � �
T I M E
� �
1 2 :
� �
A M
0 0
Press
MENU
to exit.
A
• Make sure to press
ENTER
after adjusting the time. Otherwise,
the time will not be set.
• When “DST” is set to “ON”, the time entered is forwarded by 1
hour.
• Please be sure to set “DST” before setting “TIME”.
2
3
A
• CLOCK:
The AUTO CLOCK setting may take from several minutes to an
hour depending on the number of channels to receive and signal
status.
• EDS CH < AUTO >:
If there are no channels with EDS signals or the antenna signal
is weak, the AUTO CLOCK Setting may not operate. In such a
case, the message “EDS CH IS NOT AVAILABLE.” appears, and
the CLOCK setting screen (in step
4
in
AUTO CLOCK Setting
)
is displayed. Refer to
MANUAL CLOCK Setting
to set the clock
manually.
• EDS CH < Not AUTO >:
If the channel you have selected for “EDS CH” is wrong or the
EDS signal carrier is weak, or when there is no broadcast, the
AUTO CLOCK Setting may not operate. In such cases, the
message “EDS CH (XXX) EDS DATA IS NOT AVAILABLE.”
appears, and the CLOCK setting screen (in step
4
in
AUTO
CLOCK Setting
) is displayed as in the case with EDS CH
< AUTO >. Follow step
4
and repeat the AUTO CLOCK Setting
procedure.
• If broadcasting channels are not memorized, EDS signals cannot
be received even when the “EDS CH” is set to “AUTO”. In this
case, try EZ SETUP again. (See page
25
.)
2
5
1
4
LC-20D30U_E_book.indb 16
2005/12/15 11:26:29
