Shark KLIK N' FLIP S6001UK, Руководство пользователя

Страница: 5 / 9

7 8 0800 862 0453 sharkclean.eu
IMPORTANT: Make sure you do not use the Steam Mop without attaching a Dirt Grip ™ pad and adding water to
the water tank first. When you are using the Steam Mop for the first time, it might take longer than the normal
30 seconds to start steaming.
IMPORTANT: Do not use on unsealed wood or unglazed ceramic floors. On surfaces that have been treated with
wax and on some no-wax floors, the sheen may be removed by the heat and steam action. Test an isolated area
of the surface to be cleaned before proceeding. Check the use and care instructions from the floor manufacturer.
Using Your Steam Pocket
®
Mop
fig. 9 fig. 10 fig. 11b
fig. 11a
TO SANITIZE* WITH THE STEAM MOP USING THE GENIUS ™ MOP HEAD AND THE DIRT GRIP ™ PAD:
1
Attach a clean Dirt Grip pad to the Genius Mop Head.
2
Plug into an electrical outlet. The blue light will illuminate. It takes approximately 30 seconds for the mop to heat up
and the steam to be ready.
3
Pump the handle a few times in a downward motion. This pumping action will release steam as you Steam Mop,
and allows you to customize the amount of steam you want.
4
Start mopping on an appropriate sealed hard-floor surface with a forward and backward motion. After three minutes,
your unit is ready to be used to sanitize.
5 Using a forward and backward motion, move the unit over the area you seek to sanitize. Repeat at least 15 times.
* Sanitization studies were conducted under controlled test conditions. Household conditions and results may vary.
Genius Mop Head only when used with Steam Mop. Not in Steam Blaster
™
mode.
Manual Steam Control
SETTING IDEAL FOR THESE SEALED
SURFACES
RECOMMENDED USAGE
MANUAL
Laminate
Hardwood
Marble
Tile
Stone
Cleaning sealed surfaces and large areas
Basic, everyday cleaning
Removing spots and smaller messes
Cleaning moderate and heavy traffic areas
Steam Blaster
™
For an extra burst of steam, you can use the Steam Blaster. Follow the instructions found on
the “Using your Steam Pocket
®
Mop” page.
NOTE: To prolong the life of your Steam Mop, we
recommend using distilled water.
NOTE:
Sweep or vacuum your floors prior to
cleaning with your Steam Mop.
1
Twist the Quick-Release Cord Holder to unwrap
the power cord completely (fig. 9) . Plug into an
electrical outlet. The blue light will illuminate. It takes
approximately 30 seconds for the Steam Mop to
heat up.
2
Pump the handle a few times, pushing the handle
toward the mop head in a downward, fast pumping
motion. This pumping action will release steam
as you mop with a forward or backward motion.
Customize the amount of steam by mopping slowly
for less steam and quickly for more steam.
3
Begin mopping with a forward and backward motion.
The natural motion of mopping will produce steam.
4
When you need an extra burst of steam to clean
a stuck-on stain, you can use the Steam Blaster ™
feature. Flip the head over so that it is behind the
mop body, then tilt the mop handle down. This will
cause the the Steam Blaster
(fig. 10) to emit a
concentrated blast of steam onto the stain.
CAUTION: While in Steam Blaster mode, do not
leave stationary for more than one minute.
CAUTION: Do not scrub any one area for an
extended period of time.
5
To stop the Steam Blaster spray, simply raise the
handle. You can then flip the mop head back into its
original position and continue cleaning.
6
To remove the Dirt Grip pad, simply lift the Steam Mop
straight up by the handle until the Genius Mop Head is
hanging straight down. Press the Release button on the
back of the Steam Mop body
(fig 11a) , and both sides
of the head will drop open, releasing the pad
(fig 11b)
.
7 Once the Dirt Grip pad has been released, close the
Genius Mop Head. To close, gently press one side
of the Genius Mop Head to the floor until that side
clicks into place. Repeat on the other side.
8
When the water tank is empty, the Steam Mop will
stop producing steam. You can refill the water tank
at any time as long as the Steam Mop is unplugged.
Follow the water tank filling instructions on page 6.
NOTE: Please wait 2 to 3 minutes for the Steam
Mop to cool off before switching the mop head.
Never leave the Steam Mop with a damp/wet Dirt
Grip pad on any floor for an extended period of time.